The CCU Supports both 4K and HD Formats by just Changing the Camera Head.
It Enables a High-quality, Long-distance Optical Fiber Transmission Camera System to be Configured at a Reduced Cost.
- Optical fiber transmission of uncompressed video signals over a distance of approx. 2,000 m between camera and CCU*.
- The compact, lightweight unit measures 2U in height and is rack-mountable.
- Supports IP streaming (100 Base-T).
- An SD memory card can be used for saving user files and updating firmware versions.
- * When power is supplied from CCU.
Supported Formats
| 4K (3G-SDI x 4)*1 | 3840 x 2160/59.94p, 50p, 29.97p, 25p, 23.98p |
|---|---|
| HD (3G-SDI) | 1080/59.94p, 50p, 59.94i, 50i, 23.98p over 59.94i, 29.97PsF, 25PsF, 23.98PsF, 720/59.94p, 50p |
| HD High Speed (3G-SDI x 4)*2 |
1080/239.76p, 200p |
| SD | 480/59.94i, 576/50i |
- *1: When AK-UC3000 4K Studio Handy Camera is connected.
- *2: When AK-HC5000 HD Studio Handy Camera is connected.
Input / Output
| 4K MODE*1 | SDI OUT x 4 (4K), SDI OUT x 3, SDI OUT (PM) x 1, VBS x 1, VBS (PM) x 1 |
|---|---|
| HS MODE*2 | SDI OUT x 4 (HS), SDI OUT x 3, SDI OUT (PM) x 1, VBS x 1, VBS (PM) x 1 |
SDI OUT x 7, SDI OUT (PM) x 1, VBS x 1, etc.
RET Input (SDI: 4ch, VBS: 1ch) etc.
LAN-TRUNK output
PROMPT Input (SDI : 1ch, ANALOG : 2ch)
- *1: When AK-UC3000 4K Studio Handy Camera is connected.
- *2: When AK-HC5000 HD Studio Handy Camera is connected.
Rear View
Specifications
| Power Supply | AK-UCU500P/AK-UCU500PS | 100 V - 120 V AC, 50 Hz/60 Hz |
|---|---|---|
| AK-UCU500E/AK-UCU500ES | 100 V - 240 V AC, 50 Hz/60 Hz | |
| Power Consumption | 500 W (Without camera connected: 70 W) | |
| Capacity for Supplying Power to a Camera | 240 V AC (tolerance: 5%), 1.46 A , 50 Hz/60 Hz | |
| Operating Temperature | 0 ℃ to 40 ℃ (32 °F to 104 °F) | |
| Humidity | 10 % to 90 % (no condensation) | |
| Weight | Approx. 8.8 kg (19.4 lb) | |
| Dimensions (W x H x D) | 424 mm x 88 mm x 401 mm (16-5/8 inches x 3-7/16 inches x 15-13/16 inches) (excluding protrusions) |
|
| Video Output | 3G/HD/SD-SDI | 7 lines (embedded audio is supported only for HD signals) |
| HD/SD-SDI | 1 line (shared with picture monitor output*1; embedded audio is supported only for HD signals) |
|
| Analog composite | 2 lines (1 line shared with picture monitor output*1) | |
| HD TRUNK Output | HD-SDI | 1 line (cannot be used in UHD/HS mode) |
| Return Input | 3G-HD/HD/SD-SDI | 4 lines (RET1 input has active-through output) |
| Analog composite | 1 lines | |
| Prompter Input | HD-SDI | 1 line (with active-through output) |
| Analog composite | 2 lines (through output of 1 and input of 2 share the connector*1) It is not terminated when the unit is turned OFF. No through output |
|
| Reference Input | BB (black burst) / tri-level*2: 1 line (automatic termination, connect to upper connector; BB signal and tri-level signal automatically recognized, with loop-through output) |
|
| Microphone Output | 0 dBm/600 Ω, 2 lines (XLR, 3-pin, male) | |
| Communication | Intercom input/output (ENG / PROD, 0 dBm, 600 Ω (4 W) / 1 V [p-p], 200 Ω (RTS), 4 W / RTS / CLRCOM): 2 lines*1 | |
| PGM input (0 dBm/600 Ω) : 2 lines | ||
| Tally input (red, green, yellow) : 1 input each | ||
| AUX | WFM control 6-bit (open collector output, terminal shared with camera microphone gain setting*1) |
|
| Camera microphone gain setting input 5-bit (photo-coupler input, terminal shared with WFM control*1) |
||
| Down-conversion system setting input 2-bit (photo-coupler input) | ||
| TRUNK | RS-422 / RS-232C 2 lines*1 |
|
| FRONT ROP | RS-422 1 line, 16 V DC output (only one of this and REAR ROP can be selected at one time via the menu or the [ROP FRONT/REAR] selection switch on the front panel) |
|
| REAR ROP | RS-422 1 line, 16 V DC output (only one of this and FRONT ROP can be selected at one time via the menu or the [ROP FRONT/REAR] selection switch on the front panel) |
|
| MSU | RS-422 1 line, GPI for control |
|
| LAN TRUNK | LAN connection with camera side via an optical cable*3 1 line, 100BASE-T, 1000BASE-T |
|
| LAN | Personal computer connection for distribution via the Web*3 1 line, 10BASE-T, 100BASE-TX (use a crossover cable when connecting directly with a personal computer) |
|
- *1: Depending on the setting, only one of them can be selected at one time.
- *2: The BB (black burst) signal and tri-level sync signal of the reference input are recognized automatically.
- *3: IP video cannot be transmitted when [CCU MODE] is set to [2160/23.98p], [2160/23.98PsF], [1080/23.98p], or [1080/23.98PsF].
