[OUTPUT SETTINGS]

[RAW OUTPUT]

Sets if the RAW output from the <SDI OUT 1>/<SDI OUT 2> terminal will be dual output (DUAL) or single output (SINGLE).

• Factory setting$$ [DUAL]

It can be set to [SINGLE] only when the following three conditions are fulfilled. It will be fixed to [DUAL] for all other cases.

• When [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [FREQUENCY] is set to [29.97p] or lower

• When [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [SDI RAW] is set to [4K/10bit] or [UHD/10bit]

• When [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [MAIN CODEC] is set to [AVC-Intra4K 422]

[SDI REC REMOTE]

Sets if the recording operation control function against the external device (such as recorder) connected to the <SDI OUT 1>/<SDI OUT 2> terminal is used or not.

It can be output from the <SDI OUT 2> terminal only when [SDI OUT 2 SIGNAL SEL] is set to [SDI OUT 1].

The recording operation can be controlled only when the camera is recording.

[ON]: Controls the recording operation of the external device.

[OFF]: Does not control the recording operation of the external device.

• Factory setting$$ [OFF]

[SDI OUT FORMAT]

Selects the signal to be output from the <SDI OUT 1>/<SDI OUT 2> terminal.

It is output in the HD (1920×1080) format letterbox regardless of the [MAIN PIXEL] setting.

Item that can be selected depends on the [FREQUENCY] setting. This can be selected only when [FREQUENCY] is set to [50.00p] or [59.94p].

When [FREQUENCY] is set to [23.98p]: [23.98PsF]

When [FREQUENCY] is set to [24.00p]: [24.00PsF]

When [FREQUENCY] is set to [25.00p]: [25.00PsF]

When [FREQUENCY] is set to [29.97p]: [29.97PsF]

When [FREQUENCY] is set to [50.00p]: [50.00p]/[50.00i]

When [FREQUENCY] is set to [59.94p]: [59.94p]/[59.94i]

When [FREQUENCY] is set to [50.00i]: [50.00i]

When [FREQUENCY] is set to [59.94i]: [59.94i]

• Factory setting$$ [23.98PsF]

[3G-SDI OUT]

Sets the format for the 3G-SDI signal output from the <SDI OUT 1>/<SDI OUT 2> terminal.

[LEVEL-A]: Selects the LEVEL-A method.

[LEVEL-B]: Selects the LEVEL-B DL method.

• Factory setting$$ [LEVEL-B]

[SDI OUT 2 SIGNAL SEL]

Sets the output from the <SDI OUT 2> terminal.

[SDI OUT 1]: Same output as the <SDI OUT 1> terminal.

[VF SDI]: Same output as the <VF SDI> terminal.

• Factory setting$$ [SDI OUT 1]

[SDI OUT 1 CLEAN VIEW]

Sets if the output from the <SDI OUT 1> terminal will be video only or to superimpose the signal for marker or indicator.

[ON]: Outputs video only.

[OFF]: Outputs the signals for video and marker or indicator.

• Factory setting$$ [OFF]

[SDI OUT 2 CLEAN VIEW]

Sets if the output from the <SDI OUT 2> terminal will be video only or to superimpose the signal for marker or indicator.

[ON]: Outputs video only.

[OFF]: Outputs the signals for video and marker or indicator.

• Factory setting$$ [OFF]

[MENU DISP]

Sets if the menu is displayed in the output from the <SDI OUT 1>/<SDI OUT 2> terminal.

• Factory setting$$ [OFF]

[PLAY DISP & CTRL]

Sets if the PLAY screen is displayed in the output from the <SDI OUT 1>/<SDI OUT 2> terminal, and playback control is performed or not with the remote operation panel AK-HRP200G.

• Factory setting$$ [OFF]

[PROCESSED RAW SW]

Sets whether to output RAW signal with shading adjusted information baked in. This can be selected only when [MAIN COLOR] is set to anything other than [V-Log].

• Factory setting$$ [OFF]

[VF SDI OUT FORMAT]

Selects the signal to be output from the <VF SDI> terminal.

It is output in the HD (1920×1080) format regardless of the [MAIN PIXEL] setting.

The items that can be set differ depending on the settings of [FREQUENCY] and [MAIN CODEC].

When [FREQUENCY] is set to [23.98p]: [23.98PsF]

When [FREQUENCY] is set to [24.00p]: [24.00PsF]

When [FREQUENCY] is set to [25.00p]: [25.00PsF]

When [FREQUENCY] is set to [29.97p]: [29.97PsF]

When [FREQUENCY] is set to [23.98p]: [23.98PsF]/[59.94p]/[59.94i]

When [FREQUENCY] is set to [24.00p]: [24.00PsF]/[60.00p]/[60.00i]

When [FREQUENCY] is set to [25.00p]: [25.00PsF]/[50.00p]/[50.00i]

When [FREQUENCY] is set to [29.97p]: [29.97PsF]/[59.94p]/[59.94i]

When [FREQUENCY] is set to [50.00p]: [50.00p]/[50.00i]

When [FREQUENCY] is set to [59.94p]: [59.94p]/[59.94i]

When [FREQUENCY] is set to [50.00i]: [50.00i]

When [FREQUENCY] is set to [59.94i]: [59.94i]

• Factory setting$$ [59.94p]

[3G-SDI OUT]

Sets the format of the 3G SDI signal output from the <VF SDI> terminal.

[LEVEL-A]: Selects the LEVEL-A method.

[LEVEL-B]: Selects the LEVEL-B DL method.

• Factory setting$$ [LEVEL-B]

[VF SDI CLEAN VIEW]

Sets if the output from the <VF SDI> terminal will be video only or to superimpose the signal for marker or indicator.

[ON]: Outputs video only.

[OFF]: Outputs the signals for video and marker or indicator.

• Factory setting$$ [OFF]

[SURROUND VIEW SW]

Selects enable/disable of the surround view function (a function to display the video outside the valid area to the viewfinder).

• Factory setting$$ [OFF]

[SURROUND VIEW AREA]

Selects the area for the surround view.

The recorded video will shift approximately 396 µm upward from the center of the lens when [LOWER] is selected. Take caution when using a zoom lens.

• Factory setting$$ [UPPER (NORMAL)]

[SURROUND VIEW LINE SW]

Selects enable/disable of the line mark display function for valid area.

• Factory setting$$ [ON]

[SURROUND VIEW COLOR]

Selects the color of the line mark for valid area.

• Factory setting$$ [WHITE]

[SURROUND VIEW LEVEL]

Sets the mask level against the surround signal.

• Factory setting$$ [OFF]

[MENU DISP]

Select the switch to display menu on the output from the <VF SDI> terminal.

[ON]: Can be controlled using the <MENU> button at the side of the main body, control panel, and remote operation panel.

[OFF]: Can only be controlled using the <MENU> button at the side of the main body.

• Factory setting$$ [OFF]

[SDI OUT 1 SW]

Switches display/hide of the item to set with [SDI OUT INDICATOR] to the output from the <SDI OUT 1> terminal.

[ON]: Items are individually displayed/hidden.

[OFF]: Hides all.

• Factory setting$$ [ON]

[SDI OUT 2 SW]

Switches display/hide of the item to set with [SDI OUT INDICATOR] to the output from the <SDI OUT 2> terminal.

[ON]: Items are individually displayed/hidden.

[OFF]: Hides all.

• Factory setting$$ [ON]

[SYSTEM PIXEL]

Switches display/hide of the system pixels.

• Factory setting$$ [ON]

[REC FORMAT]

Switches display/hide of the recording format display.

• Factory setting$$ [ON]

[REC MODE]

Switches display/hide of the status for the interval recording or the pre-recording.

• Factory setting$$ [ON]

[VFR]

Switches display/hide of the variable frame rate status.

• Factory setting$$ [ON]

[FPS]

Switches display/hide of the frame rate.

• Factory setting$$ [ON]

[SHUTTER]

Switches display/hide of the shutter speed.

• Factory setting$$ [ON]

[EI]

Switches display/hide of EXPOSURE INDEX.

• Factory setting$$ [ON]

[WHITE]

Switches display/hide of the color temperature.

• Factory setting$$ [ON]

[IRIS]

Switches display/hide of the iris value.

• Factory setting$$ [ON]

[FOCUS]

Switches display/hide of the focus distance.

• Factory setting$$ [ON]

[ZOOM]

Switches display/hide of the zoom value.

• Factory setting$$ [ON]

[FILTER]

Switches display/hide of the optical filter transmittance.

• Factory setting$$ [ON]

[EXTENDER]

Switches display/hide of the extender.

• Factory setting$$ [ON]

[Y GET]

Switches display/hide of the brightness of Y GET.

• Factory setting$$ [ON]

[TC]

Switches display/hide of the time code, user bits, and duration counter displays.

• Factory setting$$ [TCG/TCR]

[P2 CARD REMAIN]

Switches display/hide of the remaining recording free space of a P2 card.

• Factory setting$$ [ON]

[BATTERY REMAIN]

Switches display/hide of the remaining battery charge level.

• Factory setting$$ [ON]

[GPS]

Switches display/hide of GPS signal reception status.

• Factory setting$$ [ON]

[CLIP NAME]

Switches display/hide of the clip names.

• Factory setting$$ [ON]

[USER CLIP NAME (TYPE3)]

Switches display/hide of the user clip name when [MENU] → [REC SETTINGS] → [REC META DATA] → [USER CLIP NAME] is set to [TYPE3].

• Factory setting$$ [OFF]

[AUDIO LEVEL METER]

Switches display/hide of the audio level meter.

• Factory setting$$ [OFF]

[REMOTE CTRL]

Switches display/hide of ROP app control status.

• Factory setting$$ [ON]

[SDI OUT 1 SW]

Switches display/hide of the marker display against the output from the <SDI OUT 1> terminal.

• Factory setting$$ [OFF]

[SDI OUT 2 SW]

Switches display/hide of the marker display against the output from the <SDI OUT 2> terminal.

• Factory setting$$ [OFF]

[PB MARKER SW]

Switches display/hide of the marker display against the playback video output from the <SDI OUT 1>/<SDI OUT 2> terminal.

• Factory setting$$ [OFF]

[MARKER & CHAR LEVEL]

Sets the marker and character luminance.

[50%] - [100%] (10% step)

• Factory setting$$ [70%]

[CENTER MARKER]

Switches the center marker.

[1]: + (large)

[2]: Open center (large)

[3]: + (medium)

[4]: Open center (medium)

[5]: + (small)

[6]: Open center (small)

[7]: + (very small)

[OFF]: Does not display.

• Factory setting$$ [1]

[SAFETY MARKER]

Selects the type of frame for the safety zone marker.

[1]: Box

[2]: Corners

[OFF]: Does not display.

• Factory setting$$ [OFF]

[SAFETY AREA]

Sets the size of the safety zone marker.

[80%] - [100%] (1% step, fixed aspect ratio)

• Factory setting$$ [90%]

[FRAME MARK]

Switches enable/disable of the frame marker.

• Factory setting$$ [OFF]

[FRAME COLOR]

Sets the color of the frame marker.

• Factory setting$$ [WHITE]

[FRAME SIG]

Sets frame marker aspect ratio.

• Factory setting$$ [2.39$$1]

[- CUSTOM ASPECT]

Sets the aspect ratio when the aspect ratio of the frame marker is set to [CUSTOM].

• Factory setting$$ [2.39$$1]

[FRAME LEVEL]

Sets the level of the outside of the frame marker.

[0%] - [100%] (10% step)

• Factory setting$$ [100%]

[USER BOX]

Switches display/hide of the user box.

• Factory setting$$ [OFF]

[USER BOX WIDTH]

Sets the width of the user box.

• Factory setting$$ [13]

[USER BOX HEIGHT]

Sets the height of the user box.

• Factory setting$$ [13]

[USER BOX H POS]

Sets the horizontal position of the center of the user box.

• Factory setting$$ [0]

[USER BOX V POS]

Sets the vertical position of the center of the user box.

• Factory setting$$ [0]

[VF SDI SW]

Displays/hides the items to be set in [VF SDI INDICATOR] on the image output from the <VF SDI> terminal and on the control panel screen.

[ON]: Items are individually displayed/hidden.

[OFF]: Hides all.

• Factory setting$$ [ON]

[SYSTEM PIXEL]

Displays/hides system pixels.

[ON], [OFF]

• Factory setting$$ [ON]

[REC FORMAT]

Displays/hides recording format display.

[ON], [OFF]

• Factory setting$$ [ON]

[REC MODE]

Displays/hides the status for the interval recording or the pre-recording.

• Factory setting$$ [ON]

[VFR]

Displays/hides the variable frame rate status.

• Factory setting$$ [ON]

[FPS]

Displays/hides [FPS].

[ON], [OFF]

• Factory setting$$ [ON]

[SHUTTER]

Displays/hides shutter speed.

[ON], [OFF]

• Factory setting$$ [ON]

[EI]

Displays/hides EXPOSURE INDEX.

[ON], [OFF]

• Factory setting$$ [ON]

[WHITE]

Displays/hides color temperature.

[ON], [OFF]

• Factory setting$$ [ON]

[IRIS]

Displays/hides iris value.

[ON], [OFF]

• Factory setting$$ [ON]

[FOCUS]

Displays/hides focus distance.

[ON], [OFF]

• Factory setting$$ [ON]

[ZOOM]

Displays/hides zoom value.

[ON], [OFF]

• Factory setting$$ [ON]

[FILTER]

Displays/hides the optical filter transmittance.

[ON], [OFF]

• Factory setting$$ [ON]

[EXTENDER]

Displays/hides the extender.

[ON], [OFF]

• Factory setting$$ [ON]

[Y GET]

Displays/hides brightness of Y GET.

[ON], [OFF]

• Factory setting$$ [ON]

[TC]

Displays/hides the time code, user bits, and duration counter displays.

[TCG/TCR], [TCG], [OFF]

• Factory setting$$ [TCG/TCR]

[P2 CARD REMAIN]

Displays/hides the display of the remaining recording free space of a P2 card.

[ON], [OFF]

• Factory setting$$ [ON]

[BATTERY REMAIN]

Displays/hides the remaining battery charge level.

[ON], [OFF]

• Factory setting$$ [ON]

[GPS]

Displays/hides GPS signal reception status.

[ON], [OFF]

• Factory setting$$ [ON]

[REC TALLY]

Displays/hides the method of displaying the recording status.

[RED]: The red tally lamp lights up.

[GREEN]: The green tally lamp lights up.

[CHAR]: The characters [REC] are displayed in the viewfinder.

Regardless of this setting, when [SDI REC REMOTE] is set to [ON], or [SDI RAW] is set to anything other than [OFF], the red tally lamp will illuminate during recording with an external device.

• Factory setting$$ [RED]

[CLIP NAME]

Displays/hides clip names.

[ON], [OFF]

• Factory setting$$ [OFF]

[USER CLIP NAME (TYPE3)]

Switches display/hide of the user clip name when [MENU] → [REC SETTINGS] → [REC META DATA] → [USER CLIP NAME] is set to [TYPE3].

• Factory setting$$ [OFF]

[AUDIO LEVEL METER]

Switches display/hide of the audio level meter.

• Factory setting$$ [OFF]

[REMOTE CTRL]

Switches display/hide of ROP app control status.

• Factory setting$$ [ON]

[VF SDI SW]

Switches display/hide of the marker display against the output from the <VF SDI> terminal and the control panel screen.

[ON], [OFF]

• Factory setting$$ [ON]

[PB MARKER SW]

Switches display/hide of the marker display against the playback video output from the <VF SDI> terminal and the control panel screen.

• Factory setting$$ [OFF]

[MARKER & CHAR LVL]

Sets the marker and character luminance.

[50%], [60%], [70%]

• Factory setting$$ [50%]

[CENTER MARKER]

Switches the center marker.

[1]: + (large)

[2]: Open center (large)

[3]: + (medium)

[4]: Open center (medium)

[5]: + (small)

[6]: Open center (small)

[7]: + (very small)

[OFF]: Does not display.

• Factory setting$$ [1]

[SAFETY MARKER]

Selects the type of frame for the safety zone marker.

[1]: Box

[2]: Corners

[OFF]: Does not display.

• Factory setting$$ [OFF]

[SAFETY AREA]

Sets the size of the safety zone marker.

[80%] - [100%] (1% step, constant aspect ratio)

• Factory setting$$ [90%]

[FRAME MARK]

Switches enable/disable of the frame marker.

[ON], [OFF]

• Factory setting$$ [OFF]

[FRAME SIG]

Sets frame marker aspect ratio.

[1.33$$1], [1.44$$1], [1.56$$1], [1.78$$1], [1.85$$1], [2.00$$1], [2.201$$1], [2.35$$1], [2.39$$1], [CUSTOM]

• Factory setting$$ [2.39$$1]

[- CUSTOM ASPECT]

Sets the aspect ratio when the aspect ratio of the frame marker is set to [CUSTOM].

• Factory setting$$ [2.39$$1]

[FRAME COLOR]

Sets the color of the frame marker.

• Factory setting$$ [WHITE]

[FRAME LEVEL]

Sets the level of the outside of the frame marker.

[0%] - [100%] (10% step)

• Factory setting$$ [100%]

[USER BOX]

Switches enable/disable of the user box display.

[ON], [OFF]

• Factory setting$$ [OFF]

[USER BOX WIDTH]

Sets the width of the user box.

[1] - [100]

• Factory setting$$ [13]

[USER BOX HEIGHT]

Sets the height of the user box.

[1] - [100]

• Factory setting$$ [13]

[USER BOX H POS]

Sets the horizontal position of the center of the user box.

[−50] - [50]

• Factory setting$$ [0]

[USER BOX V POS]

Sets the vertical position of the center of the user box.

[−50] - [50]

• Factory setting$$ [0]

[EXPAND MODE]

Sets the enlargement display function mode.

[10SEC]: Disables the enlarged display function after ten seconds have elapsed.

[HOLD]: Enables the enlarged display function.

[UNTIL REC]: Enables the enlarged display function until performing recording operation.

• Factory setting$$ [10SEC]

[EXPAND1 SW]

Switches display/hide of the enlargement display function 1.

[ON], [OFF]

• Factory setting$$ [OFF]

[- POS1]

Adjusts the source signal position in an enlarged display.

[0] - [8]

• Factory setting$$ [4]

[- VALUE1]

Adjusts the enlargement factor.

[x2], [x3], [x4]

• Factory setting$$ [x2]

[EXPAND2 SW]

Switches display/hide of the enlargement display function 2.

[ON], [OFF]

• Factory setting$$ [OFF]

[- POS2]

Adjusts the source signal position in an enlarged display.

[0] - [8]

• Factory setting$$ [4]

[- VALUE2]

Adjusts the enlargement factor.

[x2], [x3], [x4]

• Factory setting$$ [x2]

[FOCUS IN COLOR SW]

Displays/hides the peaking function.

[ON], [OFF]

• Factory setting$$ [OFF]

[- PEAKING VALUE]

Sets the peaking function mode.

[LOW], [MID], [HIGH]

• Factory setting$$ [MID]

[- COLOR SEL]

Sets the peaking function color.

[RED], [GREEN], [WHITE]

• Factory setting$$ [RED]

[- MONO]

Switches enable/disable of the monochrome display function when the peaking function is displayed.

Even if it is set to [OFF], background image is displayed in monochrome when [MONO SW] is set to [ON].

If it is set to [ON], background image is displayed in monochrome even when [MONO SW] is set to [OFF].

• Factory setting$$ [OFF]

[FOCUS SQUARES SW]

Displays/hides the focus square function.

[ON], [OFF]

• Factory setting$$ [OFF]

[MONO SW]

Switches enable/disable of monochrome display function.

[ON], [OFF]

Even if it is set to [OFF], background image is displayed in monochrome when [- MONO] is set to [ON].

If it is set to [ON], background image is displayed in monochrome even when [- MONO] is set to [OFF].

• Factory setting$$ [OFF]

[FOCUS DISP]

Sets the unit for the focus distance display.

[Meter], [Feet]

• Factory setting$$ [Feet]

[OPEN IRIS FOCUS SW]

Switches enable/disable of the open iris focus assist function.

• Factory setting$$ [OFF]

[VALUE]

Sets the time for the open iris focus is to assist.

• Factory setting$$ [10SEC]

[ZEBRA SW]

Sets if the zebra signal is superimposed or not to the output from the <VF SDI> terminal.

[ON], [OFF]

• Factory setting$$ [OFF]

[- ZEBRA1 DETECT]

Sets the detection level of zebra pattern 1.

[0%] - [109%]

• Factory setting$$ [80%]

[- ZEBRA2 DETECT]

Sets the extraction level of zebra pattern 2.

[0%] - [109%]

• Factory setting$$ [100%]

[- ZEBRA2]

Enables/disables zebra pattern 2 and selects [SPOT].

[ON], [SPOT], [OFF]

• Factory setting$$ [OFF]

[WFM SW]

Displays/hides waveform monitor.

Saturation level of the video signal is displayed with a dotted line.

CDL/3D LUT is not applicable for the wave form monitor display.

• Factory setting$$ [OFF]

[- TYPE]

Sets the display format of the waveform monitor.

• Factory setting$$ [Y]

[- TRANSPARENCE]

Sets the transparency of the waveform monitor display.

• Factory setting$$ [50%]

[Y GET SW]

Switches enable/disable of the Y GET display function.

The user box function will not operate when [Y GET SW] is set to [ON].

• Factory setting$$ [OFF]

[- UNIT]

Sets the [Y GET] display unit.

It is fixed to [%] when [MENU] → [SCENE FILE SETTINGS] → [GAMMA] → [GAMMA SELECT] is set to [HLG], [BC GAMMA], [VIDEO45], or [VIDEO50].

• Factory setting$$ [STOP]

[- AREA SIZE]

Sets the size of area to detect with the Y GET display function.

• Factory setting$$ [M]

[EXPOSURE MAP SW]

Switches display/hide of the exposure map.

• Factory setting$$ [OFF]

[EXPOSURE MAP SEL]

Sets the type of the exposure map.

It is fixed to [FALSE] when [MENU] → [SCENE FILE SETTINGS] → [GAMMA] → [GAMMA SELECT] is set to [HLG], [BC GAMMA], [VIDEO45], or [VIDEO50].

• Factory setting$$ [FALSE]

[SMOOTH MODE]

Switches enable/disable of the smooth mode (a function to smooth the video of the viewfinder when the 24P, half shutter function is operated).

[ON], [OFF]

• Factory setting$$ [OFF]

[TEST SIG SEL]

Sets the test signal output.

It will not operate when [MAIN PIXEL] is set to [2048×1080 CROP] or [1920×1080 CROP].

[OFF]: Does not output a test signal.

[BARS]: Outputs the color bar set in [COLOR BARS TYPE].

• Factory setting$$ [OFF]

[COLOR BARS TYPE]

Sets the color bar to be used.

[SMPTE]: Uses the color bar of the SMPTE standard.

[FULL]: Uses the full color bar.

• Factory setting$$ [SMPTE]