| General | ||
|---|---|---|
| Power Requirements | DC 12 V to 21.8 V (DC IN connector), DC 42 V to 57 V (PoE++ power supply) | |
| Current Consumption | 3.1 A to 5.5 A (DC IN connector), 1.2 A (PoE++ power supply) | |
| Ambient Operating Temperature | -15 °C to 45 °C (5 °F to 113 °F) (preheating is required when -5 °C (23 °F) or less) | |
| Allowable Humidity Ranges | 10% to 100% (no condensation) | |
| Storage Temperature | -20 °C to 50 °C (-4 °F to 122 °F) | |
| Storage Humidity | 10% to 95% (no condensation) | |
| Mass | Approx. 9.0 kg (19.84 lb) | |
| Dimensions (W x H x D) | 258 mm x 357 mm x 397 mm (10-5/32 inches x 14-1/16 inches x 15-5/8 inches) (including protrusions and cable cover) |
|
| Finish | Silver, salt resistant coating | |
| Waterproof and Dust Proof | IP65 compliant | |
| Maximum Permissible Wind Speed |
15 m/sec: Operates normally, 50 m/sec: Operation possible, 60 m/sec: No damage | |
| Wiper | Installed as standard | |
| Heater | Installed as standard | |
| Defroster | Installed as standard | |
| Controller Supported | AW-RP150, AW-RP60, AK-HRP1010GJ*1, AK-HRP1015GJ (Not available in some areas), AK-HRP250GJ • It may be necessary to upgrade the version of the controller in order to support the unit. |
|
| Camera Unit | ||
| Imaging Sensors | 1/2.86-type Full-HD 3MOS | |
| Lens | Optical 20x zoom/10x digital zoom, F1.6 to F3.4 (f=4.5 mm to 90 mm; 35 mm equivalent: 32.13 mm to 642.5 mm) |
|
| Focus | Switching between auto and manual | |
| Focus Distance | Entire zooming range: 800 mm (2.62 ft), Wide end: 400 mm (1.31 ft) | |
| Color Separation Optical System | 3MOS | |
| Minimum Illumination | 2 lx (50 IRE, F1.6, 36 dB, without accumulation) | |
| Horizontal Resolution | 1000 TV lines Typ (Center area) | |
| Gain Selection | Auto, 0 dB to 42 dB (1 dB steps), 37 dB to 42 dB is Super Gain Mode | |
| Frame Mix | 0 dB, 6 dB, 12 dB, 18 dB, 24 dB • This cannot be configured when the format is 1080/29.97p, 1080/23.98p, 1080/29.97PsF, 1080/23.98PsF, 1080/25p, or 1080/25PsF. • When [Iris Mode] or [Focus Mode] is set to [Auto], this cannot be set to 18 dB or 24 dB. |
|
| Electronic Shutter Speed | 59.94p/59.94i | 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 |
| 29.97p | 1/30, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 | |
| 23.98p | 1/24, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 | |
| 50p/50i | 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 | |
| 25p | 1/25, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 | |
| Synchro Scan | 59.94 Hz | 60.15 Hz to 642.21 Hz (255 steps) |
| 50 Hz | 50.15 Hz to 535.71 Hz (255 steps) | |
| Gamma | HD, FILMLIKE1, FILMLIKE2, FILMLIKE3, 0.30 to 0.75 (Manual setting) | |
| White Balance | AWB A, AWB B, ATW, 3200K, 5600K, VAR (2000K to 15000K) | |
| Chroma Amount Variability | OFF, -99% to 40% | |
| Scene File | Scene1, Scene2, Scene3, Scene4 | |
| Intelligent Functions | Auto function for each of accumulation, gain, iris, electronic shutter, ND, and ATW | |
| Synchronization System | ||
| Synchronization System | Internal/External synchronization (BBS/Tri-level sync) | |
| Line Input <AUDIO IN(1/2)> | Input impedance | High impedance |
| Input | • 2 channels, XLR balanced input • Input signal level: +4 dBu/0 dBu/–20 dBu (selectable in menu) • Volume variable range: –40 dB to +12 dB (can be changed in 1 dB steps in the menu) |
|
| Output | • 4 channels, superimposed over SDI output • Embedded audio output level: FS-12 dB: –12 dBFS, FS-18 dB: –18 dBFS, FS-20 dB: –20 dBFS (selectable in menu) • Sampling frequency: 48 kHz (synchronized to video) • Quantization bit rate: 24-bit (LPCM) • Audio compression format (IP): G.726, AAC-LC (High quality) |
|
| Input | ||
| Input Connector | 12V IN | XLR connector |
| G/L IN | BNC connector • BBS (Black Burst Sync), tri-level sync supported |
|
| Audio input | mini XLR connector (line input) #1: INPUT1 Common, #2: INPUT1 HOT, #3: INPUT1 COLD, #4: INPUT2 Common, #5: INPUT2 HOT, #6: INPUT2 COLD |
|
| Output | ||
| Video Output | 3G/HD-SDI OUT | SMPTE424M/SMPTE292M / 75 Ω (BNC x 2) • Level-A/Level-B supported • OSD output is possible from the SDI OUT 1/PM connector but not from the SDI OUT 2 connector. |
| Input/Output | ||
| Input/Output Connector | LAN | LAN connector for IP control / video output / Audio output / PoE++ power supply PoE++ (IEEE802.3bt Draft ver.2.0 standard) |
| RS-422 | CONTROL IN RS-422A | |
| EXT | #1: DC GND, #2: HOT, #3: COLD, #4: 12V-OUT | |
| Pan-tilt Head Unit | ||
| Installation Method | Stand-alone (Desktop) or suspended (Hanging) • To ensure safety, the unit must be secured using the mount bracket supplied. |
|
| Camera/Pan-tilt Head Control | IP connecting cable | • When connecting through a PoE++ hub: LAN cable*2 (category 5e or above, straight cable), max. 100 m (328 ft) • When a PoE++ hub is not used: LAN cable*2 (category 5 or above, straight cable) max. 100 m (328 ft) |
| AW series connecting cable/ standard protocol connecting cable |
LAN cable*2 (category 5 or above, straight cable), max. 1000 m (3280 ft) | |
| Pan/tilt Operation Speed | Maximum speed 60°/s or higher | |
| Panning Range | ±175° • For suspended installations, the positions of the pins that determine the movement range must be changed. |
|
| Tilting range | -30° to 210 • Depending on the pan or tilt position, the camera may be reflected in the image. • For suspended installations, the positions of the pins that determine the movement range must be changed. |
|
| Quietness | 60°/s (NC45 or less) | |
| Vibration Correction | D.I.S.S. (Dynamic Image Stabilizing System) | |
- *1: Support for connection to the AK-HRP1010GJ is planned in future.
- *2: Use of an STP (shielded twisted pair) cable is recommended.
- • When connecting directly to a controller without an Ethernet hub, use a cross cable.
