[REC SETTINGS] menu

Sets the various items in the recording function.

[CARDS/MEDIA]

[FORMAT MEDIA]

Formats the SD card in the specified slot. Data deleted as a result of formatting cannot be restored. Always confirm the data before formatting.

The items that can be selected are as follows.

  • [SLOT1], [SLOT2]

[CLIP NAME]

[CAM INDEX]

Sets the CAM INDEX used in the name for the MOV format file to be recorded. Set one upper case alphabetical character. This is used as a value to be stored in the volume label of the SD card.

The items that can be set are as follows.

  • [A]…[Z]

(Factory setting: [A])

[NEXT REEL COUNT]

Sets the REEL COUNT used in the name for the MOV format file to be recorded. The setting value of [NEXT REEL COUNT] is stored in the volume label of the SD card as REEL COUNT together with the setting value of [CAM INDEX]. Also, the setting value will increase one after storing. (It will return to [001] after [999])

  • When the SD card is formatted

  • When recorded to the SD card where REEL COUNT is not stored in the volume label

The items that can be set are as follows.

  • [001]…[999]

(Factory setting: [001])

[2 SLOTS FUNC.]

Sets the recording function using two SD cards.

[OFF]

Does not set.

[RELAY REC]

Sets to relay recording.

[SIMUL REC]

Sets to simultaneous recording.

(Factory setting: [RELAY REC])

[PRE REC]

Sets whether to perform pre-recording.

The pre-recording time differs depending on the setting of the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [MAIN PIXEL]/[MAIN CODEC].

[ON]

Performs the pre-recording.

The pre-recording time is as follows.

  • When [MAIN PIXEL] is [1280x720], [1920x1080], or [2048x1080]: Approximately 10 seconds

  • When [MAIN CODEC] is [422ALL-I 400M]: Approximately 3 seconds

  • Other than above: Approximately 5 seconds

[OFF]

Does not perform the pre-recording.

(Factory setting: [OFF])

[REC FUNCTION]

[REC MODE]

Selects the recording mode.

[NORMAL]

Performs the standard recording.

[INTERVAL]

Performs the interval recording. (A function to repeatedly perform the operation of one frame recording in set time interval.)

(Factory setting: [NORMAL])

[INTERVAL TIME]

Sets the interval duration for interval recording.

The items that can be set are as follows.

  • [1s], [2s], [5s], [10s], [30s], [1min], [5min], [10min]

(Factory setting: [5min])

[TC]

[SET TC]

Sets the default value of the time code to record.

Hour

[00]…[23]

Minute

[00]…[59]

Second

[00]…[59]

Frame

[00] … [23] (when [24.00p] or [23.98p] is set)

[00] … [24] (when [50.00i], [50.00p], or [25.00p] is set)

[00] … [29] (when [59.94i], [59.94p], or [29.97p] is set)

(Factory setting: [00]) (each item)

[SET UB]

Sets user bits.

Enabled only when [USER] is selected in [UB MODE] of [TC].

Each digit can be set in following range.

  • [00]…[FF]

(Factory setting: [00])

[TC/UB/Dur.]

Switches the time code display to the user bits or duration counter display.

The items that can be set are as follows.

[TC]

Time code display

[UB]

User bits display

[Dur.]

Duration counter display

(Factory setting: [TC])

[FREE/REC RUN]

Sets the operation mode to advance the time code generator.

[FREE RUN]

Advances regardless of the operation mode.

[REC RUN]

Advances only while recording.

(Factory setting: [FREE RUN])

[DF/NDF]

Sets the count method for the time code generator.

Enabled only when the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [FREQUENCY] → [59.94i]/[59.94p]/[29.97p] is set.

[DF]

Uses the drop frame mode.

[NDF]

Uses the non-drop frame mode.

(Factory setting: [NDF])

[UB MODE]

Selects the user bits mode. User bits information is recorded in the clip. Also, it is output as LTC UB, VITC UB of the SDI signal.

[FRAME RATE]

Selects the image information (such as frame rate) of the camera.

[USER]

Selects the user bits set in [SET UB].

[TIME]

Selects the local time. (hh, mm, ss)

[DATE]

Selects the local date and time. (YY, MM, DD, hh)

[CLIP NAME]

ASCII character code of the CAM INDEX (A to Z) recorded as a MOV format file goes into MSB. Also, three digit ASCII character code of the REEL COUNT recorded as the MOV format file goes into LSB. (Example: A123=0x41 0x31 0x32 0x33) It will record even if the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [MAIN CODEC] is not set to the MOV format.

(Factory setting: [USER])

[TC IN/OUT SEL]

Sets the input/output of the <TC IN/OUT> terminal.

[TC IN]

Sets to the time code input.

[TC OUT]

Sets to the time code output.

(Factory setting: [TC IN])

[TC OUT REF]

Sets the output delay of the time code that is output from the <TC IN/OUT> terminal.

[RECORDING]

Outputs the recording time code without delay. This is used when performing simultaneous recording on two cameras with the time code of this camera as the master.

[SDI OUT]

Matches to output image from the <SDI OUT> terminal. Outputs without delay when video is not output from the <SDI OUT> terminal.

(Factory setting: [RECORDING])