[SYSTEM SETTINGS]

Sets the system in general.

Item

Description of settings

[SYSTEM MODE]

[SYSTEM RESTART]

Restarts the camera when selected.

This is displayed when any of the settings requiring a restart after the change ([FREQUENCY]/[SDI RAW]/[MAIN PIXEL]/[MAIN CODEC]/[HIGH SPEED] in [SYSTEM MODE]) is changed.

[PLEASE SYSTEM RESTART] is displayed on the [SYSTEM MODE] screen, and it will not move to any other setting other than [SYSTEM MODE]. However, each setting in [SYSTEM MODE] can still be set. Other operation such as recording will not be possible.

[FREQUENCY]

Sets the system frequency.

The basic system of the camera is determined by five settings of [FREQUENCY]/[SDI RAW]/[MAIN PIXEL]/[MAIN CODEC]/[HIGH SPEED]. Restarting the system is necessary if basic system setting is changed. Dialog prompting for restart is displayed when one of the 5 settings is changed. Restart by operating the power switch of the camera, or by pressing the jog dial button and following the on-screen instruction.

[23.98p], [24.00p], [25.00p], [29.97p], [50.00p], [59.94p], [50.00i], [59.94i]

  • Factory setting: [23.98p]

[SDI RAW]

Sets the number of RAW pixels and the bit depth of the output from the <SDI OUT 1>/<SDI OUT 2> terminal.

[OFF], [4K/10bit], [4K/12bit], [2K/10bit], [UHD/10bit], [UHD/12bit], [HD/10bit]

  • Factory setting: [OFF]

[MAIN PIXEL]

Sets the main recorder’s number of recording pixels.

Selectable items vary depending on the [SDI RAW] setting.

[4096×2160], [3840×2160], [2048×1080], [2048×1080 CROP], [1920×1080], [1920×1080 CROP]

  • Factory setting: [4096×2160]

Selectable items vary when [SDI RAW] is set as follows.

  • [2048×1080 CROP]/[1920×1080 CROP] cannot be selected when it is set to [OFF].

  • Only [2048×1080] can be selected when it is set to [4K/12bit].

  • Only [1920×1080] can be selected when it is set to [UHD/12bit].

[MAIN CODEC]

Sets the recording codec of the main recorder. Selectable items vary depending on the [FREQUENCY]/[SDI RAW]/[MAIN PIXEL] setting.

[AVC-Intra4K 422], [AVC-Intra4K-LT], [AVC-Intra2K 444], [AVC-Intra2K 422], [AVC-Intra2K-LT], [AVC-Intra444], [AVC-Intra422], [AVC-Intra-LT], [AVC-Intra100], [AVC-LongG50], [AVC-LongG25], [ProRes 4444 XQ], [ProRes 4444], [ProRes 422 HQ], [ProRes 422], [ProRes 422 LT], [OFF]

[OFF] can be set when [SDI RAW] is set to anything other than [OFF].

  • Factory setting: [AVC-Intra4K 422]

[PROXY CODEC]

Sets the codec of the proxy recording.

At the same time, it switches enable/disable of the proxy data recording.

[AVC-Proxy G6], [OFF]

  • Factory setting: [OFF]

[PROXY SLOT]

Sets the slot to record the proxy.

[MAIN & SUB], [MAIN], [SUB]

[NORMAL+Audio] cannot be recorded when the variable frame rate function is enabled with [MAIN & SUB], [MAIN].

The proxy recorded in the SD memory card cannot be transferred via network.

  • Factory setting: [MAIN & SUB]

[VFR PROXY REC]

Sets the operation of the sub recorder during the variable frame rate operation.

[VFR up to 60p (50p)], [NORMAL+Audio]

  • Factory setting: [VFR up to 60p]

[HIGH SPEED]

Sets the frame rate when [SDI RAW] is set to [2K/10bit] or [HD/10bit], and [MAIN CODEC] is set to [OFF].

[OFF], [ON]

  • Factory setting: [OFF]

[COLOR SETTINGS]

[MAIN]

Sets the colors of videos (entire camera system) recorded in the main recorder.

[V-Log]/[SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]/[SHADING]

  • Factory setting: [V-Log]

[GRADING]

Sets whether to apply the grading process.

This only enabled when [V-Log] is set in [MAIN].

[Internal]: Sets grading with the control panel.

[OFF]: Disables the grading process.

[External App]: Sets the grading using an external application.

[SHADING]: Sets the shading assuming the use of external ROP.

  • Factory setting: [OFF]

[PROXY]

Sets the color of video recorded as proxy.

Selectable items vary depending on the [MAIN] setting.

When [MAIN] is set to [V-Log] and [GRADING] is set to [Internal] or [External App]

[V-Log]/[GRADING]

When [MAIN] is set to [V-Log] and [GRADING] is set to [SHADING]

[BAKED IN]/[V-Log]

When [MAIN] is set to [V-Log] and [GRADING] is set to [OFF]

[V-Log]/[V-709]

When [MAIN] is set to [SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]

[SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]

When [MAIN] is set to [SHADING]

[BAKED IN]

  • Factory setting: [V-Log]

[SDI OUT 1]

Sets the output image from the <SDI OUT 1> terminal.

Selectable items vary depending on the [MAIN] setting.

When [MAIN] is set to [V-Log] and [GRADING] is set to [Internal] or [External App]

[V-Log]/[GRADING]

When [MAIN] is set to [V-Log] and [GRADING] is set to [SHADING]

[BAKED IN]/[V-Log]

When [MAIN] is set to [V-Log] and [GRADING] is set to [OFF]

[V-Log]/[V-709]

When [MAIN] is set to [SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]

[SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]

When [MAIN] is set to [SHADING]

[BAKED IN]

  • Factory setting: [V-Log]

[SDI OUT 2]

Sets the output image from the <SDI OUT 2> terminal.

Selectable items vary depending on the [MAIN] setting.

When [MAIN] is set to [V-Log] and [GRADING] is set to [Internal] or [External App]

[V-Log]/[GRADING]

When [MAIN] is set to [V-Log] and [GRADING] is set to [SHADING]

[BAKED IN]/[V-Log]

When [MAIN] is set to [V-Log] and [GRADING] is set to [OFF]

[V-Log]/[V-709]

When [MAIN] is set to [SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]

[SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]

When [MAIN] is set to [SHADING]

[BAKED IN]

  • Factory setting: [V-Log]

[VF SDI]

Sets the output image from the <VF SDI> terminal.

Selectable items vary depending on the [MAIN] setting.

When [MAIN] is set to [V-Log] and [GRADING] is set to [Internal] or [External App]

[V-Log]/[GRADING]

  • [V-Log]/[V-709] when [SURROUND VIEW SW] is set to [ON].

When [MAIN] is set to [V-Log] and [GRADING] is set to [SHADING]

[BAKED IN]/[V-Log]

When [MAIN] is set to [V-Log] and [GRADING] is set to [OFF]

[V-Log]/[V-709]

When [MAIN] is set to [SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]

[SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]

When [MAIN] is set to [SHADING]

[BAKED IN]

  • Factory setting: [V-Log]

[DETAIL SW]

Enables/disables the detail function.

[ON], [OFF]

  • Factory setting: [OFF]

[DETAIL CORING]

Sets the coring amount for the detail signal.

[0] - [15] (1 step)

  • Factory setting: [1]

[DETAIL LEVEL]

Sets the effect level for the detail signal.

[0] - [15] (1 step)

  • Factory setting: [5]

[3D LUT]

Sets the grading process method when [GRADING] is set to anything other than [OFF], or when [MAIN] is set to [SHADING] and [GAMMA SELECT] is set to [V-Log].

When [GRADING] is set to anything other than [OFF], or when [MAIN] is set to [SHADING] and [GAMMA SELECT] is set to [V-Log].

[OFF]/[V-709]/[LOADED FILE]

[FILE SEL]: Reads the 3D LUT applied when [LOADED FILE] is selected from the SD memory card.

[SAVE AS(SD CARD)]: Writes the 3D LUT applied currently to the SD memory card.

When [GRADING] is set to [OFF], or when [MAIN] is set to [SHADING] and [GAMMA SELECT] is set to [BC GAMMA].

[OFF]

  • Factory setting: [OFF]

[PLAYBACK GRADING]

Sets if the grading process is applied or not on the playback video.

[OFF], [ON]

  • Factory setting: [OFF]

[CDL]

Sets the grading process method when [GRADING] is set to [Internal] or [External App].

When [GRADING] is set to [Internal] or [External App]

[ON]/[OFF]

[FILE SEL]: Reads the CDL setting from the SD memory card.

[SAVE AS(SD CARD)]: Writes the current CDL setting to the SD memory card.

When [GRADING] is set to [OFF] or [SHADING]

[OFF]

  • Factory setting: [OFF]

[SLOPE-R]

Sets the value of [SLOPE-R].

[0.50] - [2.00] (0.01 step)

  • Factory setting: [1.00]

[SLOPE-G]

Sets the value of [SLOPE-G].

[0.50] - [2.00] (0.01 step)

  • Factory setting: [1.00]

[SLOPE-B]

Sets the value of [SLOPE-B].

[0.50] - [2.00] (0.01 step)

  • Factory setting: [1.00]

[OFFSET-R]

Sets the value of [OFFSET-R].

[−0.50] - [0.50] (0.01 step)

  • Factory setting: [0.00]

[OFFSET-G]

Sets the value of [OFFSET-G].

[−0.50] - [0.50] (0.01 step)

  • Factory setting: [0.00]

[OFFSET-B]

Sets the value of [OFFSET-B].

[−0.50] - [0.50] (0.01 step)

  • Factory setting: [0.00]

[POWER-R]

Sets the value of [POWER-R].

[0.50] - [2.00] (0.01 step)

  • Factory setting: [1.00]

[POWER-G]

Sets the value of [POWER-G].

[0.50] - [2.00] (0.01 step)

  • Factory setting: [1.00]

[POWER-B]

Sets the value of [POWER-B].

[0.50] - [2.00] (0.01 step)

  • Factory setting: [1.00]

[SATURATION]

Sets the value of [SATURATION].

[0.00] - [2.00] (0.01 step)

  • Factory setting: [1.00]

[R GAIN]

Adjusts the gain of Rch when [GRADING] is set to [SHADING].

[−200] - [+200] (1 step)

  • Factory setting: [0]

[G GAIN]

Adjusts the gain of Gch when [GRADING] is set to [SHADING].

[−200] - [+200] (1 step)

  • Factory setting: [0]

[B GAIN]

Adjusts the gain of Bch when [GRADING] is set to [SHADING].

[−200] - [+200] (1 step)

  • Factory setting: [0]

[M.PED]

Adjusts the level of the master pedestal when [GRADING] is set to [SHADING].

[−100] - [+100] (1 step)

  • Factory setting: [0]

[R PED]

Adjusts the pedestal level of Rch when [GRADING] is set to [SHADING].

[−100] - [+100] (1 step)

  • Factory setting: [0]

[G PED]

Adjusts the pedestal level of Gch when [GRADING] is set to [SHADING].

[−100] - [+100] (1 step)

  • Factory setting: [0]

[B PED]

Adjusts the pedestal level of Bch when [GRADING] is set to [SHADING].

[−100] - [+100] (1 step)

  • Factory setting: [0]

[MASTER GAMMA]

Adjusts the gamma characteristic when [GRADING] is set to [SHADING].

[−50] - [+50] (1 step)

  • Factory setting: [0]

[R GAMMA]

Adjusts the gamma characteristic of the red against the master gamma when [GRADING] is set to [SHADING].

[−15] - [+15] (1 step)

  • Factory setting: [0]

[B GAMMA]

Adjusts the gamma characteristic of the blue against the master gamma when [GRADING] is set to [SHADING].

[−15] - [+15] (1 step)

  • Factory setting: [0]

[CHROMA LEVEL]

Adjust the chroma level of the PR signal and the PB signal when [GRADING] is set to [SHADING].

[−99%] - [99%]

  • Factory setting: [0%]

[ANAMORPHIC DESQUEEZE]

[PROXY & SDI OUT]

Sets if the video to be recorded in the proxy and the SDI output video is to be de-squeezed.

[ON], [OFF]

  • Factory setting: [OFF]

[VF SDI]

Sets if the output video from the <VF SDI> terminal is to be de-squeezed.

[ON], [OFF]

  • Factory setting: [OFF]

[DESQUEEZE RATIO]

Sets the de-squeeze ratio.

[1.3x]: De-squeeze 1.3 times in horizontal direction.

[1.3xmag]: It will be in aspect ratio of 2.39:1 for mastering generated from the image de-squeezed 1.3 times in horizontal direction.

[2.0x]: De-squeeze 2.0 times in horizontal direction.

[2.0xmag]: It will be in aspect ratio of 2.39:1 for mastering generated from the image de-squeezed 2.0 times in horizontal direction.

  • Factory setting: [1.3x]

[IMAGE INVERT]

[PROXY & SDI OUT]

Sets if the video to be recorded in the proxy and the SDI output video is to be inverted.

The thumbnail of the clip to be recorded in the main slot is reversed when set to [ON]. (The recorded video is not reversed.)

[ON], [OFF]

  • Factory setting: [OFF]

[VF SDI]

Sets if the output video from the <VF SDI> terminal is to be inverted.

[ON], [OFF]

  • Factory setting: [OFF]

[INVERT SELECT]

Sets the type of inversion.

[HORIZONTAL]: Invert horizontally

[VERTICAL]: Invert vertically

[180° ROTATE]: Invert vertically and horizontally

  • Factory setting: [HORIZONTAL]

[USER SWITCHES]

[USER1]

Sets the function to be assigned to the <USER 1> button.

[INHIBIT], [SIX USER BUTTONS], [AWB], [Y GET], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [WFM], [BARS], [ONE PUSH A. IRIS], [FALSE COLOR], [ZEBRA], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [VF SDI CLEAN], [VF SDI MARKER], [VF SDI DESQUEEZE], [VF SDI IMAGE INVERT], [SMOOTH MODE], [TEXT MEMO], [SHOT MARK], [REC SW], [AUDIO MON VOL], [AUDIO IN VOL], [AUDIO MONITOR CH], [DIRECT VOL CTRL], [VFR SW], [CHECK LAST CLIP START], [CHECK LAST CLIP END], [RETURN]

Even if [BARS] is assigned, this item will not operate when [MAIN PIXEL] is set to [2048×1080 CROP]/[1920×1080 CROP].

The color bar is not output from the <SDI OUT 1>/<SDI OUT 2> terminal even if [BARS] is assigned when [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].

  • Factory setting: [INHIBIT]

[USER2]

Sets the function to be assigned to the <USER 2> button.

[INHIBIT], [SIX USER BUTTONS], [AWB], [Y GET], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [WFM], [BARS], [ONE PUSH A. IRIS], [FALSE COLOR], [ZEBRA], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [VF SDI CLEAN], [VF SDI MARKER], [VF SDI DESQUEEZE], [VF SDI IMAGE INVERT], [SMOOTH MODE], [TEXT MEMO], [SHOT MARK], [REC SW], [AUDIO MON VOL], [AUDIO IN VOL], [AUDIO MONITOR CH], [DIRECT VOL CTRL], [VFR SW], [CHECK LAST CLIP START], [CHECK LAST CLIP END], [RETURN]

Even if [BARS] is assigned, this item will not operate when [MAIN PIXEL] is set to [2048×1080 CROP]/[1920×1080 CROP].

The color bar is not output from the <SDI OUT 1>/<SDI OUT 2> terminal even if [BARS] is assigned when [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].

  • Factory setting: [INHIBIT]

[USER3]

Sets the function to be assigned to the <USER 3> button.

[INHIBIT], [SIX USER BUTTONS], [AWB], [Y GET], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [WFM], [BARS], [ONE PUSH A. IRIS], [FALSE COLOR], [ZEBRA], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [VF SDI CLEAN], [VF SDI MARKER], [VF SDI DESQUEEZE], [VF SDI IMAGE INVERT], [SMOOTH MODE], [TEXT MEMO], [SHOT MARK], [REC SW], [AUDIO MON VOL], [AUDIO IN VOL], [AUDIO MONITOR CH], [DIRECT VOL CTRL], [VFR SW], [CHECK LAST CLIP START], [CHECK LAST CLIP END], [RETURN]

Even if [BARS] is assigned, this item will not operate when [MAIN PIXEL] is set to [2048×1080 CROP]/[1920×1080 CROP].

The color bar is not output from the <SDI OUT 1>/<SDI OUT 2> terminal even if [BARS] is assigned when [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].

  • Factory setting: [INHIBIT]

[USER TOGGLE(USER4)]

Sets the function to be assigned to the <TOGGLE/WB> button.

[WB], [SHUTTER], [EI]

  • Factory setting: [WB]

[USER5]

Sets the function to be assigned to the control panel operation button. The control panel operation button functions as a USER button.

Assign [SIX USER BUTTONS] to the <USER 1> to <USER 3> buttons.

[INHIBIT], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [FALSE COLOR], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [SMOOTH MODE], [VFR SW]

  • Factory setting: [INHIBIT]

[USER6]

Sets the function to be assigned to the control panel operation button. The control panel operation button functions as a USER button.

Assign [SIX USER BUTTONS] to the <USER 1> to <USER 3> buttons.

[INHIBIT], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [FALSE COLOR], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [SMOOTH MODE], [VFR SW]

  • Factory setting: [INHIBIT]

[USER7]

Sets the function to be assigned to the control panel operation button. The control panel operation button functions as a USER button.

Assign [SIX USER BUTTONS] to the <USER 1> to <USER 3> buttons.

[INHIBIT], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [FALSE COLOR], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [SMOOTH MODE], [VFR SW]

  • Factory setting: [INHIBIT]

[USER8]

Sets the function to be assigned to the control panel operation button. The control panel operation button functions as a USER button.

Assign [SIX USER BUTTONS] to the <USER 1> to <USER 3> buttons.

[INHIBIT], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [FALSE COLOR], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [SMOOTH MODE], [VFR SW]

  • Factory setting: [INHIBIT]

[USER9]

Sets the function to be assigned to the control panel operation button. The control panel operation button functions as a USER button.

Assign [SIX USER BUTTONS] to the <USER 1> to <USER 3> buttons.

[INHIBIT], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [FALSE COLOR], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [SMOOTH MODE], [VFR SW]

  • Factory setting: [INHIBIT]

[USER10]

Sets the function to be assigned to the control panel operation button. The control panel operation button functions as a USER button.

Assign [SIX USER BUTTONS] to the <USER 1> to <USER 3> buttons.

[INHIBIT], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [FALSE COLOR], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [SMOOTH MODE], [VFR SW]

  • Factory setting: [INHIBIT]

[USER GRIP1]

Sets the function to be assigned to the <USER GRIP1> button of the grip module.

[INHIBIT], [SIX USER BUTTONS], [AWB], [Y GET], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [WFM], [BARS], [ONE PUSH A. IRIS], [FALSE COLOR], [ZEBRA], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [VF SDI CLEAN], [VF SDI MARKER], [VF SDI DESQUEEZE], [VF SDI IMAGE INVERT], [SMOOTH MODE], [TEXT MEMO], [SHOT MARK], [REC SW], [AUDIO MON VOL], [AUDIO IN VOL], [AUDIO MONITOR CH], [DIRECT VOL CTRL], [VFR SW], [RETURN]

Even if [BARS] is assigned, this item will not operate when [MAIN PIXEL] is set to [2048×1080 CROP]/[1920×1080 CROP].

The color bar is not output from the <SDI OUT 1>/<SDI OUT 2> terminal even if [BARS] is assigned when [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].

  • Factory setting: [INHIBIT]

[USER GRIP2]

Sets the function to be assigned to the <USER GRIP2> button of the grip module.

[INHIBIT], [SIX USER BUTTONS], [AWB], [Y GET], [EXPAND1], [EXPAND2], [OPEN IRIS F.A.], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.], [WFM], [BARS], [ONE PUSH A. IRIS], [FALSE COLOR], [ZEBRA], [VF SDI COLOR], [SDI OUT 1 COLOR], [SDI OUT 2 COLOR], [VF SDI CLEAN], [VF SDI MARKER], [VF SDI DESQUEEZE], [VF SDI IMAGE INVERT], [SMOOTH MODE], [TEXT MEMO], [SHOT MARK], [REC SW], [AUDIO MON VOL], [AUDIO IN VOL], [AUDIO MONITOR CH], [DIRECT VOL CTRL], [VFR SW], [RETURN]

Even if [BARS] is assigned, this item will not operate when [MAIN PIXEL] is set to [2048×1080 CROP]/[1920×1080 CROP].

The color bar is not output from the <SDI OUT 1>/<SDI OUT 2> terminal even if [BARS] is assigned when [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].

  • Factory setting: [INHIBIT]

[LENS RET SW]

Sets the function to be assigned to the <RET> button of lens.

[INHIBIT], [RETURN], [EXPAND1], [EXPAND2], [IN COLOR F.A.], [SQ. F.A.], [MONO F.A.]

  • Factory setting: [RETURN]

[SIDE LOCK]

[REC(FRONT)]

Sets if the <REC> button on the camera is to be locked or not with the <LOCK> switch on the camera.

[LOCK]: It will be locked.

[UNLOCK]: It will not be locked.

  • Factory setting: [UNLOCK]

[USER1/PLAY]

Sets if the <USER1>/<PLAY> button is to be locked or not with the <LOCK> switch on the camera.

[LOCK]: It will be locked.

[UNLOCK]: It will not be locked.

  • Factory setting: [LOCK]

[USER2/INFO]

Sets if the <USER2>/<INFO> button is to be locked or not with the <LOCK> switch on the camera.

[LOCK]: It will be locked.

[UNLOCK]: It will not be locked.

  • Factory setting: [LOCK]

[USER3/EXT]

Sets if the <USER3>/<EXT> button is to be locked or not with the <LOCK> switch on the camera.

[LOCK]: It will be locked.

[UNLOCK]: It will not be locked.

  • Factory setting: [LOCK]

[IRIS/SEL]

Sets if the <IRIS/SEL> dial button is to be locked or not with the <LOCK> switch on the camera.

[LOCK]: It will be locked.

[UNLOCK]: It will not be locked.

  • Factory setting: [LOCK]

[MENU]

Sets if the <MENU> button is to be locked or not with the <LOCK> switch on the camera.

[LOCK]: It will be locked.

[UNLOCK]: It will not be locked.

  • Factory setting: [LOCK]

[SYS CHECK]

Sets if the <SYSTEM CHK> button is to be locked or not with the <LOCK> switch on the camera.

[LOCK]: It will be locked.

[UNLOCK]: It will not be locked.

  • Factory setting: [LOCK]

[TOGGLE]

Sets if the <TOGGLE/WB> is to be locked or not with the <LOCK> switch on the camera.

[LOCK]: It will be locked.

[UNLOCK]: It will not be locked.

  • Factory setting: [LOCK]

[PLAYBACK SETTING]

[PLAYBACK MODE]

Specifies the playback mode of the PLAY screen.

[SINGLE]: Plays back only the clip in the cursor position.

[CONTINUOUS]: Continuously plays back the clips in the list.

  • Factory setting: [SINGLE]

[CARDS/MEDIA]

[FORMAT MEDIA]

Formats the card in the specified slot after the format menu is selected.

[MAIN SLOT], [SUB SLOT]

Data deleted as a result of formatting cannot be restored. Always check the data before formatting.

[MEDIA END ALARM]

Sets if the alarm is to be sounded when there is no remaining capacity in the memory card.

[ON], [OFF]

  • Factory setting: [ON]

[POWER MANAGEMENT]

[DC IN SOURCE]

Sets the type of the external power supply input into the <DC IN> terminal.

[DC POWER SUPPLY]: Selected when connecting an AC adaptor. In this case, the remaining battery charge level is not displayed.

[BATTERY]: Selected when connecting a battery to the <DC IN> terminal. Remaining charge level is detected from the voltage level.

  • Factory setting: [DC POWER SUPPLY]

[DC IN BATTERY SETTINGS]

Following items are settings for the external battery connected to the <DC IN> terminal.

[- FULL VOLT]

Sets the voltage to be displayed in the remaining charge level full display when an external battery is input from the <DC IN> terminal.

[13.0V] - [17.0V] (0.1 V step)

  • Factory setting: [15.5V]

[- NEAR END VOLT]

Sets the remaining charge level near end voltage when an external battery is input from the <DC IN> terminal.

[11.0V] - [15.0V] (0.1 V step)

  • Factory setting: [13.2V]

[- END VOLT]

Sets the remaining charge level end voltage when an external battery is input from the <DC IN> terminal.

[11.0V] - [15.0V] (0.1 V step)

  • Factory setting: [12.5V]

[ONBOARD BATTERY SETTINGS]

Following items are settings for the external battery connected to the battery holder.

[- BATTERY SELECT]

Selected according to the battery used.

[DIONIC], [HyTRON], [ENDURA], [PAG]: The remaining charge level is detected and a warning is displayed according to the [- NEAR END INFO] and [- END VOLT] settings. When there is no remaining charge level information, the remaining charge level is detected from the voltage level.

[other]: Remaining charge level is detected from the voltage level.

  • Factory setting: [DIONIC]

[- FULL VOLT]

Sets the voltage in the remaining charge level full display when the battery remaining charge level is detected from the voltage level.

[13.0V] - [17.0V] (0.1 V step)

  • Factory setting: [15.5V]

[- NEAR END VOLT]

Sets the remaining charge level near end voltage when the battery remaining charge level is detected from the voltage level.

[11.0V] - [15.0V] (0.1 V step)

  • Factory setting: [13.2V]

[- END VOLT]

Sets the remaining charge level end voltage when the battery remaining charge level is detected from the voltage level.

[11.0V] - [15.0V] (0.1 V step)

  • Factory setting: [12.5V]

[- NEAR END INFO]

Sets the percentage value of the remaining charge level near end when remaining charge level information is acquired from the battery.

[4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%]

  • Factory setting: [5%]

[- END INFO]

Sets the percentage value of the remaining charge level end when remaining charge level information is acquired from the battery.

[1%] - [10%] (1% step)

  • Factory setting: [1%]

[END ALARM]

Sets whether to sound an alarm at battery remaining charge level end.

[ON], [OFF]

  • Factory setting: [ON]

[FAN]

[FAN SPEED]

Select the rotation speed of the fan.

[REC AUTO]: The rotation speed is lowered simultaneously with start of recording. However, the fan will rotate in appropriate speed for each by [MAIN CODEC] when it reaches the specified temperature. The fan will rotate at the maximum speed when not recording.

[MATCH CODEC]: The fan will operate in rotation speed appropriate for each in accordance with [MAIN CODEC].

[ALWAYS FULL]: The fan will always rotate at the maximum speed.

[LIVE]: The fan will always rotate at low speed. However, the fan will operate in appropriate speed for each by [MAIN CODEC] when it reaches the specified temperature.

  • Factory setting: [REC AUTO]

[GENLOCK]

[GENLOCK MODE]

Switches the synchronization signal of the camera signal.

[INT]: Synchronizes to the internal standard signal.

[EXT]: Synchronizes to the entered external standard signal.

  • Factory setting: [INT]

[H PHASE COARSE]

Roughly adjusts to match horizontal synchronization phase when building a system.

[−100] - [100]

  • Factory setting: [0]

[H PHASE FINE]

Minutely adjusts to match horizontal synchronization phase when building a system.

[−100] - [100]

  • Factory setting: [0]

[CONTROL DISPLAY]

[BRIGHTNESS]

Adjusts the brightness of the control panel.

[−15] - [15]

  • Factory setting: [0]

[COLOR LEVEL]

Adjusts the color levels of the control panel.

[−15] - [15]

  • Factory setting: [0]

[CONTRAST]

Adjusts the contrast of the control panel.

[−30] - [30]

  • Factory setting: [0]

[BACK LIGHT]

Sets the brightness of the control panel backlight.

[−1]: Will be darker than [0].

[0]: Standard brightness.

[1]: Will be brighter than [0].

  • Factory setting: [0]

[BUTTON LED]

Illuminates each button of the control panel and the camera.

[ON], [OFF]

  • Factory setting: [ON]

[CLOCK]

[CLOCK SETTING]

Sets the built-in calendar (year/month/day) and time.

[YEAR]: [2016] - [2037]

[MONTH]: [JAN] - [DEC] ([1] - [12])

[DAY]: [1] - [31] ([28], [29], [30])

[HOUR]: [0] - [23]

[MINUTE]: [0] - [59]

[TIME ZONE]

Sets the time zone. After setting the time, when changing the time zone setting, the displayed and registered times switch to the time with the time difference.

[−12:00] - [+13:00]

(30-minute interval, without [+12:30] and with [+12:45])

[DATE FORMAT]

Sets the display order of year/month/day.

This is also applied to the recording date displayed in the clip properties.

[Y-M-D]/[M-D-Y]/[D-M-Y]

  • Factory setting: [Y-M-D]

[INFORMATION]

[OPERATION TIME]

[TOTAL OPERATION]: Displays the operation time of the camera.

[IRIS DIAL]: Displays the total number of upward turn or downward turn with the operation of the <IRIS/SEL> dial button on the camera every 100 operations. (“T” indicates the number.)

[VERSION]

Displays the information of the camera.

[MODEL]: Displays the product name.

[SERIAL NO.]: Displays the serial number.

[PRODUCT VERSION]: Displays the version.

[UPDATE]

Performs an update of the camera firmware. (Enabled only when there is a dedicated update file on the SD memory card.)

[YES], [NO]

[USB]

Switches the camera to mode for USB device function.

[YES], [NO]

[TRACE LOG]

Reads the camera’s execution log from an SD memory card.

[YES], [NO]

[SENSOR TEMP]

Displays the temperature around the sensor of the camera.

[LANGUAGE]

Switches the display language of the menu.

[ENGLISH], [CHINESE]

  • Factory setting: [ENGLISH]

[INITIALIZE]

[LOAD FACTORY DATA]

Returns the menu values to their factory settings.

[YES], [NO]