Alert

Screen display

Description

Behavior and cause

Camera image screen

[SIMUL REC WARNING <SLOT 2>]/[SIMUL REC WARNING <SLOT 3>]

An error has occurred in one of the memory cards during simultaneous recording.

A message is displayed for approximately five seconds.

  • Recording to the other memory card will continue.

[SIMUL REC WARNING <SLOT 2>]/[SIMUL REC WARNING <SLOT 3>]

Recording has been attempted while the number of clips has exceeded the limit on one of the memory cards during simultaneous recording.

A message is displayed for approximately five seconds.

  • Recording to the other memory card will continue.

  • [SIMUL REC WARNING <SLOT 2>] [<OVER MAX NUM. OF CLIPS>]/[SIMUL REC WARNING <SLOT 3>] [<OVER MAX NUM. OF CLIPS>] is displayed in the message display area of the STATUS screen for the mode check.

  • Replace the memory card or delete unnecessary clips.

[FAN STOPPED]

The fan has stopped.

A message is displayed.

  • The current operation will continue.

  • Stop the use immediately when the fan has stopped and alert is displayed, and consult the dealer.

  • If the fan has stopped, temperature of the camera will rise. Therefore, do not use the camera for a long period of time. Use the tripod, etc., and do not touch the camera directly.

[Non-supported card. <SLOT 1>]

[Insert expressP2 card.]

Card other than expressP2 card is inserted in the card slot 1.

A message is displayed for approximately five seconds.

  • Insert an expressP2 card.

[ENCRYPTED CARD <SLOT 1>]/[ENCRYPTED CARD <SLOT 2>]/ [ENCRYPTED CARD <SLOT 3>]

P2 card formatted with encryption with CPS (Content Protection System) password is inserted.

A message is displayed for approximately five seconds.

  • The camera does not support the CPS function of the P2 card. Insert a P2 card that is not formatted with encryption with CPS password.

  • Formatting P2 card, which was formatted with encryption with CPS password, in the camera will enable P2 card to be used as unencrypted card.

[REINSERT OR CHECK CARD <SLOT 1>]/[REINSERT OR CHECK CARD <SLOT 2>]/[REINSERT OR CHECK CARD <SLOT 3>]

The memory card cannot be recognized properly because a recording medium which is not supported has been inserted or there is dirt on the terminal of the memory card.

A message is displayed for approximately five seconds.

  • Check the memory card that is inserted.

  • Insert the memory card again if displayed when inserting a memory card.

[FORMAT ERROR CARD <SLOT 1>]/[FORMAT ERROR CARD <SLOT 2>]/[FORMAT ERROR CARD <SLOT 3>]

A memory card with management information out of specifications has been inserted.

A message is displayed for approximately five seconds.

  • Insert a memory card that can record.

[NOT SDXC CARD <SLOT 2>]/[NOT SDXC CARD <SLOT 3>]

A SDHC memory card that cannot record the MOV format data or a 32 GB microP2 card is inserted when [FILE FORMAT] is set to MOV format.

A message is displayed for approximately five seconds.

  • Insert a SDXC memory card or 64 GB microP2 card.

[INCOMPATIBLE CARD <SLOT 2>]/[INCOMPATIBLE CARD <SLOT 3>]

A memory card that may not be able to record due to slow writing speed has been inserted.

A message is displayed for approximately five seconds.

  • The current operation will continue.

  • Use a memory card with sufficient writing speed.

[DIR NG CARD <SLOT 1>]/[DIR NG CARD <SLOT 2>]/[DIR NG CARD <SLOT 3>]

A P2 card with inappropriate directory placement is inserted when [FILE FORMAT] is set to P2 format.

A message is displayed for approximately five seconds.

  • The current operation will continue.

  • Take a backup of the memory card immediately, and use it again after formatting.

[RUN DOWN CARD <SLOT 1>]/[RUN DOWN CARD <SLOT 2>]/[RUN DOWN CARD <SLOT 3>]

A P2 card exceeding the specified number of overwrites is inserted.

A message is displayed for approximately five seconds.

  • The current operation will continue.

  • Replace the P2 card.

[SD CARD <SLOT 2>]/[SD CARD <SLOT 3>]

The SD card is inserted when [FILE FORMAT] is set to P2 format and the [VIDEO OUT/LCD/VF] menu → [INDICATOR] → [SD CARD WARNING] is set to [ON].

A message is displayed for approximately five seconds.

  • The current operation will continue.

  • Set [SD CARD WARNING] to [OFF].

[SLOT1 CANNOT REC]

[microP2/SD SELECTED]

A memory card is inserted in card slot 1 when the [RECORDING] menu → [REC MEDIA] → [microP2/SD] is set.

A message is displayed for approximately five seconds.

  • Set to the [RECORDING] menu → [REC MEDIA] → [expressP2] when recording on the memory card inserted in card slot 1.

[SLOT2/3 CANNOT REC]

[expressP2 SELECTED]

A memory card is inserted in card slot 2 or card slot 3 when the [RECORDING] menu → [REC MEDIA] → [expressP2] is set.

A message is displayed for approximately five seconds.

  • Set to the [RECORDING] menu → [REC MEDIA] → [microP2/SD] when recording on the memory card inserted in card slot 2 or card slot 3.

[BACKUP BATT EMPTY]

Voltage lowering of the backup battery for internal clock was detected when the power is set to < j > (ON).

A message is displayed for approximately five seconds.

  • The current operation will continue.

  • Set the date/time again after charging the built-in battery.