Details of the connector signals

DC IN
	1	GND
	2	NC
	3	NC
	4	+12 V
	Panasonic Parts No.: K1AA104H0038 Manufacturer Parts No.: HA16RX-4P (SW1) (76) (Hirose Electric Co.) NOTE Make sure that the polarity of the external power supply is correct.

FRONT MIC IN
	1	GND
	2	L CH IN(H)
	3	L CH IN(C)
	4	R CH IN(H)
	5	R CH IN(C)
	Panasonic Parts No.: K1AB105B0002 Manufacturer Parts No.: NC5FBH (NEUTRIK)

AUDIO IN
	1	GND
	2	AUDIO IN (H)
	3	AUDIO IN (C)
	Panasonic Parts No.: K1AY103A0001 Manufacturer Parts No.: HA16PRM-3SG (72) (Hirose Electric Co.)

AUDIO OUT
	1	GND
	2	L CH OUT(H)
	3	L CH OUT(C)
	4	R CH OUT(H)
	5	R CH OUT(C)
	Panasonic Parts No.: K1AA105H0016 Manufacturer Parts No.: HA16RD-5P(76) (Hirose Electric Co.) NOTE The <AUDIO OUT> terminal on the camera is the XLR terminal and outputs balanced audio signals. To make unbalanced connection with an external device using a pin plug, release pins 3 and 5. The following is a connection example. Pin terminal Do not use the cable where the pin 3, pin 5 and pin 1 are connected. Doing so may result in a malfunction.

DC OUT
	1	GND
	2	NC
	3	NC
	4	+12 V OUT DC (11 V – 17 V) (maximum 1.5 A)
	Panasonic Parts No.: K1AY104J0001 Manufacturer Parts No.: HR10A-7R-4SC (73) (Hirose Electric Co.) Cable connector manufacturer Parts No.: HR10A-7P-4(73) (Hirose Electric Co.) NOTE Make sure the total of power taken from the <DC OUT> terminal, <VF> terminal, and <LENS> terminal does not exceed 30 W.


1	UNREG-12V	DC 12 V power supply
2	UNREG-12V	DC 12 V power supply
3	A9.0V	DC 9 V power supply (not used)
4	VF-P_B-GND	Viewfinder P_B signal GND
5	VF-P_R-GND	Viewfinder P_R signal GND
6	VF-Y	Viewfinder Y signal output
7	VF-Y-GND	Viewfinder Y signal GND
8	VF-CLK	Serial data clock pulse signal
9	VF-WR	Pulse signal for loading serial/parallel conversion data
10	VF-DATA	Serial data signal for serial/parallel conversion
11	UNREG-GND	GND
12	ZEBRA-SW	Zebra signal ON/OFF
13	PEAKING	Peaking control (not used)
14	SPARE	Spare (not used)
15	VF-P_R	Viewfinder P_R signal output
16	VF-P_B	Viewfinder P_B signal output
17	MARKER-SW	Marker ON/OFF (not used)
18	FRONT-VR	F.AUDIO LEVEL adjustment (not used)
19	VR-GND	F.AUDIO LEVEL GND (not used)
20	UNREG-GND	GND
Panasonic Parts No.: K1AB120H0001 Manufacturer Parts No.: HR12-14RA-20SC (Hirose Electric Co.) NOTE Make sure the total of power taken from the <DC OUT> terminal, <VF> terminal, and <LENS> terminal does not exceed 30 W.

LENS
	1	RET-SW
	2	REC-START/STOP
	3	GND
	4	IRIS-AUTO
	5	IRIS-CONT
	6	UNREG +12 V (max. 1.5 A)
	7	IRIS-POSI
	8	IRIS-G-MAX
	9	EXT-POSI
	10	ZOOM-POSI
	11	FOCUS-POSI
	12	SPARE
	Panasonic Parts No.: K1AY112JA001 Manufacturer Parts No.: HR10A-10R-12SC (71) (Hirose Electric Co.) NOTE Make sure the total of power taken from the <DC OUT> terminal, <VF> terminal, and <LENS> terminal does not exceed 30 W.


1	CH-1 SHIELD	GND
2	CH-1 HOT	Audio input from the wireless microphone receiver: CH1 HOT
3	CH-1 COLD	Audio input from the wireless microphone receiver: CH1 COLD
4	GND	GND
5	UNREG +12 V	Power supply to the wireless microphone receiver
6	RX ON	Power remote output to the wireless microphone receiver
7	RF WARN	RF warning input from the wireless microphone receiver
8	RM5	Not used
9	RM4	Not used
10	SPARE 1	Not used
11	SPARE 2	Not used
12	EXT CLK	Not used
13	CLK SHIELD	Not used
14	CH-2 SHIELD	GND
15	CH-2 HOT	Audio input from the wireless microphone receiver: CH2 HOT
16	CH-2 COLD	Audio input from the wireless microphone receiver: CH2 COLD
17	+5.6 V	Power supply to the wireless microphone receiver
18	VIDEO OUT	Not used
19	VIDEO RET	Not used
20	VIDEO EN	Not used
21	RM 1 (RM CLK)	Not used
22	RM 2 (RM DATA)	Not used
23	RM 3 (RM WR)	Not used
24	RM+5 V	Not used
25	RM GND	Not used
Panasonic Parts No.: K1GB25A00010 Manufacturer Parts No.: HDBB-25S (05) (Hirose Electric Co.)


1	12 V UNREG	Power supply to the light, etc. (supplied from the battery)
2	GND	GND
Panasonic Parts No.: VJS4444