[CAMERA SETTINGS]

Sets the fine quality adjustment of camera videos and camera operation.

imageicon_ENHANCED is the extended menu. Set [MENU] → [CAMERA SETTINGS] → [Enhanced] → [Enhanced SW] to [ON] to display the extended menu.

Item

Description of settings

[Enhanced]

[Enhanced SW]

Enables/disables the [Enhanced] function.

[ON]: Enables the [Enhanced] function and shows the menu related to the [Enhanced] function.

[OFF]: Disables the [Enhanced] function and hides the menu related to the [Enhanced] function.

  • Factory setting: [OFF]

[FPS]

[VFR SW]

Enables/disables the variable frame rate function.

[ON]: Enables the variable frame rate function. The desired frame rate can be set using [PRESET VALUE]/[VARIABLE VALUE]. Audio cannot be recorded.

[OFF]: Disables the variable frame rate function. [VFR SW] is fixed to [ON] when [SYSTEM SETTINGS] → [SYSTEM MODE] → [HIGH SPEED] is set to [ON (1-**fps)].

  • Factory setting: [OFF]

[FPS MODE]

Selects the frame rate setting method.

[PRESET]: Selects the frame rate from preset frame rates (maximum of 12).

Registration is done from the control panel.

[VARIABLE]: Selects the frame rate from all available frame rates.

  • Factory setting: [PRESET]

[PRESET VALUE]

Selects a value from a maximum of 12 values set from the control panel.

  • Factory setting: [24fps]

[VARIABLE VALUE]

Selects the frame rate from all available frame rates. Selectable values vary depending on [SYSTEM MODE] settings.

  • Factory setting: [24fps]

[WHITE]

[AWB]

Executes automatic white balancing.

[EXECUTE], [CANCEL]

  • Factory setting: [CANCEL]

[MODE]

Selects the white balance mode.

[PRESET]: Selects the color temperature from preset color temperatures. Registration is done from the control panel.

[TEMP SHIFT]: Selects the color temperature from all configurable color temperatures.

  • Factory setting: [PRESET]

[PRESET VALUE]

Selects a value from a maximum of 12 values set from the control panel.

Preset values that can be selected in the factory setting are [3200K+0GMg], [4300K+0GMg], [5600(5500)K+0GMg], and [6300K+0GMg].

  • Factory setting: [3200K+0GMg]

[TEMP SHIFT]

Selects the color temperature from all configurable color temperatures.

[2300K] - [15000K]

  • Factory setting: [3200K]

[GMg]

Adjusts the balance between green and magenta.

+: Adjusts toward green.

−: Adjusts toward magenta.

[−10] - [10]

  • Factory setting: [0]

[R GAIN]

imageicon_ENHANCED

Adjusts the Rch gain.

[−200] - [200]

  • Factory setting: [0]

[B GAIN]

imageicon_ENHANCED

Adjusts the Bch gain.

[−200] - [200]

  • Factory setting: [0]

[AWB OFFSET]

imageicon_ENHANCED

Sets the Rch gain and Bch gain value when performing automatic white balancing.

[ON]: Maintains and adds the values of [R GAIN] and [B GAIN] after performing automatic white balancing.

[OFF]: Resets the value of [R GAIN] and [B GAIN] after performing automatic white balancing.

  • Factory setting: [OFF]

[SHOCKLESS WHITE]

imageicon_ENHANCED

Sets the transition time when switching preset values.

[OFF]: Values are immediately switched.

[1]: Switches in approximately one second.

[2]: Switches in approximately two seconds.

[3]: Switches in approximately five seconds.

  • Factory setting: [OFF]

[BLACK]

imageicon_ENHANCED

[ABB]

imageicon_ENHANCED

Executes automatic black balancing. When executing automatic black balancing, put the cap on the lens to keep any light from entering the image sensor.

[EXECUTE], [CANCEL]

  • Factory setting: [CANCEL]

[M.PED]

imageicon_ENHANCED

Sets the master pedestal level.

[−100] - [100]

  • Factory setting: [0]

[R PED]

imageicon_ENHANCED

Adjusts the Rch pedestal level.

[−100] - [100]

  • Factory setting: [0]

[G PED]

imageicon_ENHANCED

Adjusts the Gch pedestal level.

[−100] - [100]

  • Factory setting: [0]

[B PED]

imageicon_ENHANCED

Adjusts the Bch pedestal level.

[−100] - [100]

  • Factory setting: [0]

[ABB OFFSET]

imageicon_ENHANCED

Sets the pedestal levels for Rch, Gch, and Bch after performing the adjustment of the automatic black balance.

[ON]: The values of [R PED], [G PED], and [B PED] are maintained and added even after performing the automatic black balance.

[OFF]: The values of [R PED], [G PED], and [B PED] are reset after performing the automatic black balance.

  • Factory setting: [OFF]

[INITIAL ABB]

imageicon_ENHANCED

Executes the initialization of the sensor at the same time the automatic black balance is executed.

This can be selected only when [HIGH SPEED] is set to [ON].

Keep the light away from the image sensor by placing a cap on the lens, etc., when executing the automatic black balance.

[EXECUTE], [CANCEL]

  • Factory setting: [CANCEL]

[NR]

[ISO800]

Switches the noise reduction effect in the range of ISO200 to ISO4000.

[ON], [OFF]

The range will be ISO200 to ISO2000 when [HIGH SPEED] is set to [ON].

The range will be 0 dB to 15 dB when [MODE] in [EI] is set to [dB].

  • Factory setting: [OFF]

[ISO5000]

Switches the noise reduction effect in the range of ISO5000 to ISO12800.

[ON], [OFF]

The range will be ISO2500 to ISO6400 when [HIGH SPEED] is set to [ON].

The range will be 18 dB to 24 dB when [MODE] in [EI] is set to [dB].

  • Factory setting: [OFF]

[EI]

[MODE]

Switches the EXPOSURE INDEX control unit.

[ISO], [dB]

  • Factory setting: [ISO]

[ISO SELECT]

Selects the operation of ISO.

[NATIVE ONLY], [800BASE], [5000BASE]

  • Factory setting: [NATIVE ONLY]

[NATIVE ISO]

Sets the value when [NATIVE ONLY] is selected.

[800], [5000]

The value will be [400] and [2500] when [HIGH SPEED] is set to [ON].

  • Factory setting: [800]

[800BASE ISO]

Sets the value when [800BASE] is selected.

[200], [250], [320], [400], [500], [640], [800], [1000], [1250], [1600], [2000], [2500], [3200], [4000], [5000], [6400], [8000], [10000], [12800]

It will be [200], [250], [320], [400], [500], [640], [800], [1000], [1250], [1600], [2000], [2500], [3200], [4000], [5000], and [6400] when the setting of [HIGH SPEED] is [ON].

  • Factory setting: [800]

[5000BASE ISO]

Sets the value when [5000BASE] is selected.

[1250], [1600], [2000], [2500], [3200], [4000], [5000], [6400], [8000], [10000], [12800]

It will be [1250], [1600], [2000], [2500], [3200], [4000], [5000], and [6400] when [HIGH SPEED] is set to [ON].

  • Factory setting: [5000]

[SETTING(GAIN)]

Sets the value when [dB] is selected.

[0dB], [3dB], [6dB], [9dB], [12dB], [15dB], [18dB], [21dB], [24dB]

  • Factory setting: [0dB]

[GAIN OFFSET SW]

imageicon_ENHANCED

Sets whether to perform fine adjustment of control when [dB] is selected.

[ON], [OFF]

  • Factory setting: [OFF]

[OFFSET LEVEL]

imageicon_ENHANCED

Sets the fine adjustment level.

[0.0dB] - [0.9dB] (0.1 dB step)

  • Factory setting: [0dB]

[SHUTTER]

[SW]

Enables/disables the shutter function.

[ON], [OFF]

  • Factory setting: [ON]

[DISPLAY MODE]

Sets the shutter display unit.

[sec]: Displays in time.

[deg]: Displays at shutter open angle.

  • Factory setting: [deg]

[MODE]

Switches the shutter control mode.

[PRESET]: Selects the mode from 12 modes inside the memory.

[SYNCHRO]: Selects the mode from the operable range.

  • Factory setting: [PRESET]

[SYNCHRO deg]

Sets the value of angle control ([deg]).

[1.0] - [358.0]

  • Factory setting: [180.0]

[SYNCHRO sec]

Sets the value of time control ([sec]). The lowest value changes depending on the frame rate ([FPS]) value.

[1/60] - [1/250]

  • Factory setting: [1/48]

[PRESET VALUE deg]

Selects the angle control ([deg]) value from the maximum of 12 values set in the control panel.

Preset values that can be selected in the factory setting are [11.5], [22.5], [45.0], [90.0], [120.0], [144.0], [172.8], [180.0], [270.0], and [358.0].

  • Factory setting: [180.0]

[PRESET VALUE sec]

Selects the time control ([sec]) value from the maximum of 12 values set in the control panel.

Preset values that can be selected in the factory setting are [1/60], [1/100], [1/120], [1/250], [1/500], [1/1000], and [1/2000].

  • Factory setting: [1/60]

[TEST SIG]

[TEST SIG SEL]

Sets the test signal output.

[OFF]: Does not output a test signal.

[BARS]: Outputs the color bar set in [COLOR BARS TYPE].

  • Factory setting: [OFF]

[COLOR BARS TYPE]

Set the color bar to be used.

[SMPTE]: Uses the color bar in the SMPTE standard.

[FULL]: Uses full color bars.

  • Factory setting: [SMPTE]

[DETAIL]

imageicon_ENHANCED

[SW]

imageicon_ENHANCED

Enables/disables the detail function.

[ON], [OFF]

  • Factory setting: [OFF]

[CORING]

imageicon_ENHANCED

Sets the coring amount for the detail signal.

[0] - [60]

  • Factory setting: [1]

[MASTER LEVEL]

imageicon_ENHANCED

Sets the effect level for the detail signal.

[−31] - [31]

  • Factory setting: [0]

[SKIN DETAIL]

imageicon_ENHANCED

[SW]

imageicon_ENHANCED

Enables/disables the skin tone detail function.

[OFF], [ON]

  • Factory setting: [OFF]

[TABLE SELECT]

imageicon_ENHANCED

Selects the table for the skin tone detail.

[A], [B], [C], [A+B], [A+C], [B+C], [A+B+C]

  • Factory setting: [A]

[GET]

imageicon_ENHANCED

Sets whether to register the screen center color as the color by which the skin tone detail is applied.

[EXECUTE], [CANCEL]

[ZEBRA SW]

imageicon_ENHANCED

Sets whether to superimpose the zebra signal to the color by which the skin tone detail is applied.

[ON], [OFF]

  • Factory setting: [OFF]

[EFFECT LEVEL]

imageicon_ENHANCED

Sets the effective level of the skin tone detail. The higher the value, the more significant the effect.

[0] - [31]

  • Factory setting: [16]

[DETECT TABLE]

imageicon_ENHANCED

Selects the skin tone table of the subject that displays the skin tone detail.

[A], [B], [C]

  • Factory setting: [A]

[I CENTER]

imageicon_ENHANCED

Sets the center position of the upper I axis (setting the area that displays the skin tone).

[0] - [255]

  • Factory setting: [35]

[I WIDTH]

imageicon_ENHANCED

Sets the width of the area that displays the skin tone of the upper I axis that focus on [I CENTER].

[0] - [255]

  • Factory setting: [55]

[Q WIDTH]

imageicon_ENHANCED

Sets the width of the area that displays the skin tone of the upper Q axis that focus on [I CENTER].

[0] - [127]

  • Factory setting: [22]

[Q PHASE]

imageicon_ENHANCED

Sets the phase of the area that displays the skin tone regarding to the Q axis.

[0] - [255]

  • Factory setting: [0]

[MATRIX]

imageicon_ENHANCED

[SW]

imageicon_ENHANCED

Enables/disables the matrix function.

[ON], [OFF]

  • Factory setting: [OFF]

[(R-G)_N]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(R-G)_P]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(R-B)_N]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(R-B)_P]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(G-R)_N]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(G-R)_P]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(G-B)_N]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(G-B)_P]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(B-R)_N]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(B-R)_P]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(B-G)_N]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(B-G)_P]

imageicon_ENHANCED

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[COLOR CORRECTION]

imageicon_ENHANCED

[SW]

imageicon_ENHANCED

Enables/disables the color correction function.

[ON], [OFF]

  • Factory setting: [OFF]

[R (SAT)]

imageicon_ENHANCED

Corrects red color saturation.

[−63] - [63]

  • Factory setting: [0]

[R (PHASE)]

imageicon_ENHANCED

Corrects the red hue.

[−63] - [63]

  • Factory setting: [0]

[R-Mg (SAT)]

imageicon_ENHANCED

Corrects the color saturation between red and magenta.

[−63] - [63]

  • Factory setting: [0]

[R-Mg (PHASE)]

imageicon_ENHANCED

Corrects the hue between red and magenta.

[−63] - [63]

  • Factory setting: [0]

[Mg (SAT)]

imageicon_ENHANCED

Corrects magenta color saturation.

[−63] - [63]

  • Factory setting: [0]

[Mg (PHASE)]

imageicon_ENHANCED

Corrects the magenta hue.

[−63] - [63]

  • Factory setting: [0]

[Mg-B (SAT)]

imageicon_ENHANCED

Corrects the color saturation between magenta and blue.

[−63] - [63]

  • Factory setting: [0]

[Mg-B (PHASE)]

imageicon_ENHANCED

Corrects the hue between magenta and blue.

[−63] - [63]

  • Factory setting: [0]

[B (SAT)]

imageicon_ENHANCED

Corrects blue color saturation.

[−63] - [63]

  • Factory setting: [0]

[B (PHASE)]

imageicon_ENHANCED

Corrects the blue hue.

[−63] - [63]

  • Factory setting: [0]

[B-Cy (SAT)]

imageicon_ENHANCED

Corrects the color saturation between blue and cyan.

[−63] - [63]

  • Factory setting: [0]

[B-Cy (PHASE)]

imageicon_ENHANCED

Corrects the hue between blue and cyan.

[−63] - [63]

  • Factory setting: [0]

[Cy (SAT)]

imageicon_ENHANCED

Corrects cyan color saturation.

[−63] - [63]

  • Factory setting: [0]

[Cy (PHASE)]

imageicon_ENHANCED

Corrects the cyan hue.

[−63] - [63]

  • Factory setting: [0]

[Cy-G (SAT)]

imageicon_ENHANCED

Corrects the color saturation between cyan and green.

[−63] - [63]

  • Factory setting: [0]

[Cy-G (PHASE)]

imageicon_ENHANCED

Corrects the hue between cyan and green.

[−63] - [63]

  • Factory setting: [0]

[G (SAT)]

imageicon_ENHANCED

Corrects green color saturation.

[−63] - [63]

  • Factory setting: [0]

[G (PHASE)]

imageicon_ENHANCED

Corrects the green hue.

[−63] - [63]

  • Factory setting: [0]

[G-Yl (SAT)]

imageicon_ENHANCED

Corrects the color saturation between green and yellow.

[−63] - [63]

  • Factory setting: [0]

[G-Yl (PHASE)]

imageicon_ENHANCED

Corrects the hue between green and yellow.

[−63] - [63]

  • Factory setting: [0]

[Yl (SAT)]

imageicon_ENHANCED

Corrects yellow color saturation.

[−63] - [63]

  • Factory setting: [0]

[Yl (PHASE)]

imageicon_ENHANCED

Corrects the yellow hue.

[−63] - [63]

  • Factory setting: [0]

[Yl-R (SAT)]

imageicon_ENHANCED

Corrects the color saturation between yellow and red.

[−63] - [63]

  • Factory setting: [0]

[Yl-R (PHASE)]

imageicon_ENHANCED

Corrects the hue between yellow and red.

[−63] - [63]

  • Factory setting: [0]

[SKIN CORRECTION]

imageicon_ENHANCED

[SKIN AREA SW]

imageicon_ENHANCED

Enables/disables the function which makes fine adjustments of near skin tone colors.

[ON], [OFF]

  • Factory setting: [OFF]

[SKIN AREA HUE]

imageicon_ENHANCED

Makes fine adjustments in hue.

[−63] - [63]

  • Factory setting: [0]

[SKIN AREA TONE]

imageicon_ENHANCED

Makes fine adjustments in tone.

[−63] - [63]

  • Factory setting: [0]

[EXT.FUNC]

[FOCUS DISP]

Sets the unit that displays the focus distance.

[Meter], [Feet]

  • Factory setting: [Feet]

[LENS SETTING]

[A.IRIS TYPE]

imageicon_ENHANCED

Determines whether to set the speed control to the lens volume and use the value set in the menu.

[LENS], [CAM]

  • Factory setting: [LENS]

[A.IRIS LEVEL EFFECT]

imageicon_ENHANCED

Sets the target value during auto iris operation.

[0] - [100]

  • Factory setting: [30]

[A.IRIS SPEED]

imageicon_ENHANCED

Sets the speed when the [A.IRIS TYPE] is set to [CAM].

[1] - [20]

  • Factory setting: [10]

[A.IRIS WINDOW]

imageicon_ENHANCED

Selects the auto iris detection window.

[NORMAL1]: Window that is near screen center.

[NORMAL2]: Window that is near screen bottom.

[CENTER]: Window that is a spot in the screen center.

  • Factory setting: [NORMAL1]

[A.IRIS PEAK/AVE]

imageicon_ENHANCED

Sets the ratio included in the peak for auto iris standard.

[0] - [100]

  • Factory setting: [30]

[LENS CONNECT TYPE]

Sets the type of lens to be connected.

[TYPE A]: Lens controlled with LDS (Lens Data System). (ULTRA PRIME lens not supported)

[TYPE B]: Lens controlled with 12-pin connector

[TYPE C]: Lens controlled with cooke/i communication

[OFF]: Other lenses

  • Factory setting: [OFF]