[OUTPUT SETTINGS]

Sets the display content of the output video from the viewfinder and <VF SDI> terminal.

Item		Description of settings
[SDI OUT]	[P to PsF]	Sets the segment frame for the output from terminals <SDI OUT1> to <SDI OUT4>. When [MENU] → [CAMERA SETTINGS] → [FPS] → [VFR SW] is set to [OFF] The setting is enabled when the following conditions are fulfilled. When [MENU] → [SYSTEM SETTINGS] → [MAIN PIXEL] is set to [2048×1080] or [1920×1080] When [MENU] → [SYSTEM SETTINGS] → [FREQUENCY] is set to [23.98p], [24.00p], [25.00p], or [23.98p] When [MENU] → [CAMERA SETTINGS] → [FPS] → [VFR SW] is set to [ON] The setting is enabled when the following conditions are fulfilled. When [MENU] → [SYSTEM SETTINGS] → [MAIN PIXEL] is set to [2048×1080] or [1920×1080] When [MENU] → [SYSTEM SETTINGS] → [FREQUENCY] is set to [23.98p], [24.00p], [25.00p], or [23.98p] When [MENU] → [SYSTEM SETTINGS] → [MAIN CODEC] is set to [ProRes 4444 XQ] or [ProRes 4444] [ON], [OFF] Factory setting: [OFF]
	[4K OUT TYPE]	Sets the 4K signal format to be output from terminals <SDI OUT1> to <SDI OUT4>. [SQUARE], [2 SAMPLE INT] Factory setting: [SQUARE]
	[3G-SDI OUT]	Sets the 3G SDI signal format to be output from terminals <SDI OUT1> to <SDI OUT4>. [LEVEL-A]: Selects the LEVEL-A method. [LEVEL-B]: Selects the LEVEL-B DL method. Factory setting: [LEVEL-B]
	[SDI REC REMOTE]	Sets whether to use the control function of recording operation for an external device (such as a recorder) connected to the <SDI OUT> terminal, the <MON OUT1> terminal, and the <MON OUT2> terminal. It can be output from the <MON OUT2> terminal only when [MON OUT2 SIGNAL SEL] is set to [MON OUT1]. [ON]: Controls the recording operation of the external device. [OFF]: Does not control the recording operation of the external device. Factory setting: [OFF]
[MON OUT]	[MON OUT FORMAT]	Select the signal output from the <MON OUT1> terminal and <MON OUT2> terminal. Selectable items vary depending on the settings of [MENU] → [SYSTEM SETTINGS] → [FREQUENCY] and [MENU] → [SYSTEM SETTINGS] → [MAIN CODEC]. When [FREQUENCY] is set to [23.98p]: [MAIN CODEC] is set to [AVC-Intra4K 444], [AVC-Intra2K 444], or [AVC-Intra444] [1920/23.98PsF] [MAIN CODEC] is set to anything other than [AVC-Intra4K 444], [AVC-Intra2K 444], or [AVC-Intra444] [1920/23.98PsF], [1920 over 59.94p], [1920 over 59.94i] When [FREQUENCY] is set to [24.00p]: [MAIN CODEC] is set to [AVC-Intra4K 444] or [AVC-Intra2K 444] [1920/24PsF] [MAIN CODEC] is set to anything other than [AVC-Intra4K 444] or [AVC-Intra2K 444] [1920/24PsF], [1920 over 60p], [1920 over 60i]
		When [FREQUENCY] is set to [25.00p]: [MAIN CODEC] is set to [AVC-Intra4K 444], [AVC-Intra2K 444], or [AVC-Intra444] [1920/25PsF] [MAIN CODEC] is set to anything other than [AVC-Intra4K 444], [AVC-Intra2K 444], or [AVC-Intra444] [1920/25PsF], [1920 over 50p] When [FREQUENCY] is set to [29.97p]: [MAIN CODEC] is set to [AVC-Intra4K 444], [AVC-Intra2K 444], or [AVC-Intra444] [1920/29.97PsF] [MAIN CODEC] is set to anything other than [AVC-Intra4K 444], [AVC-Intra2K 444], or [AVC-Intra444] [1920/29.97PsF], [1920 over 59.94p]
		When [FREQUENCY] is set to [50p]: [1920/50p], [1920/50i] When [FREQUENCY] is set to [50i]: [1920/50i] When [FREQUENCY] is set to [59.94p]: [1920/59.94p], [1920/59.94i] When [FREQUENCY] is set to [59.94i]: [1920/59.94i]
		Factory setting: [1920/23.98PsF]
	[3G-SDI OUT]	Sets the 3G SDI signal format to be output from the <MON OUT1> terminal and <MON OUT2> terminal. [LEVEL-A]: Selects the LEVEL-A method. [LEVEL-B]: Selects the LEVEL-B DL method. Factory setting: [LEVEL-B]
	[MON OUT2 SIGNAL SEL]	Sets the output from the <MON OUT2> terminal. [VF SDI (1080p)]: Selects the same output as the <VF SDI> terminal. The signal format will always be 1920×1080p. [VF SDI (1080i)]: Selects the same output as the <VF SDI> terminal. The signal format will always be 1920×1080i. [MON OUT1]: Selects the same output as the <MON OUT1> terminal. Factory setting: [VF (1080p)]
	[MON OUT1 STATUS]	Sets whether to show the status display on the output from the <MON OUT1> terminal. [ON], [OFF] Factory setting: [OFF]
	[MON OUT2 STATUS]	Sets whether to show the status display on the output from the <MON OUT2> terminal. [ON], [OFF] Factory setting: [OFF]
	[MENU DISP]	Sets whether to display [MENU] in the output from the <MON OUT1> terminal and <MON OUT2> terminal. [ON], [OFF] Factory setting: [ON]
	[PLAY DISP & CTRL]	Sets whether to display the PLAY screen in the output from the <MON OUT1> terminal and the <MON OUT2> terminal. [ON], [OFF] Factory setting: [OFF]
[VF OUT]	[VF SDI OUT FORMAT]	Selects the signal to output from the <VF SDI> terminal. [1080P], [1080i] Factory setting: [1080P]
	[PLAYBACK VF IMAGE]	Selects the image output from the <VF> terminal and the <VF SDI> terminal. [PLAYBACK], [CAMERA] Factory setting: [PLAYBACK]
	[SURROUND VIEW SW]	Enables/disables the surround view function (the function to display the image outside the effective range on the viewfinder). [ON], [OFF] Factory setting: [OFF]
	[SURROUND VIEW AREA]	Selects the range of the surround view. [UPPER (NORMAL)], [LOWER] The image to be recorded will shift approximately 396 µm upwards from the center of the lens when [LOWER] is selected. Take care when the zoom lens is used. Factory setting: [UPPER (NORMAL)]
	[SURROUND VIEW LINE SW]	Enables/disables the effective area line mark display function. [ON], [OFF] Factory setting: [ON]
	[SURROUND VIEW COLOR]	Sets the effective area line mark color. [WHITE], [BLACK], [RED], [GREEN], [BLUE], [YELLOW] Factory setting: [WHITE]
	[SURROUND VIEW LEVEL]	Sets the microphone level for the surround signal. [OFF], [75%], [50%], [25%] Factory setting: [OFF]
	[SMOOTH MODE]	Enables/disables the smooth mode (function which smoothens the viewfinder image when 24P and half shutter function is running). [ON], [OFF] Factory setting: [OFF]
[MON OUT INDICATOR]	[SYSTEM PIXEL]	Displays/hides system pixels. [ON], [OFF] Factory setting: [ON]
	[SYSTEM FREQ]	Displays/hides system frequency. [ON], [OFF] Factory setting: [ON]
	[REC FORMAT]	Displays/hides recording format display. [ON], [OFF] Factory setting: [ON]
	[REC MODE]	Displays/hides the status for the interval recording or the pre-recording. [ON], [OFF] Factory setting: [ON]
	[VFR]	Displays/hides the variable frame rate status. [ON], [OFF] Factory setting: [ON]
	[FPS]	Displays/hides frame rate. [ON], [OFF] Factory setting: [ON]
	[SHUTTER]	Displays/hides shutter speed. [ON], [OFF] Factory setting: [ON]
	[EI]	Displays/hides EXPOSURE INDEX. [ON], [OFF] Factory setting: [ON]
	[WHITE]	Displays/hides color temperature. [ON], [OFF] Factory setting: [ON]
	[IRIS]	Displays/hides iris value. [ON], [OFF] Factory setting: [ON]
	[FOCUS]	Displays/hides focus distance. [ON], [OFF] Factory setting: [ON]
	[ZOOM]	Displays/hides zoom value. [ON], [OFF] Factory setting: [ON]
	[FILTER]	Displays/hides the optical filter transmittance. [ON], [OFF] Factory setting: [ON]
	[EXTENDER]	Displays/hides the extender. [ON], [OFF] Factory setting: [ON]
	[Y GET]	Displays/hides brightness of Y GET. [ON], [OFF] Factory setting: [ON]
	[TC]	Displays/hides the time code, user bits, and duration counter displays. [TCG/TCR], [TCG], [OFF] Factory setting: [TCG/TCR]
	[P2 CARD REMAIN]	Displays/hides the display of the remaining recording free space of a P2 card. [ON], [OFF] Factory setting: [ON]
	[BATTERY REMAIN]	Displays/hides the estimated remaining battery charge level. [ON], [OFF] Factory setting: [ON]
	[PROXY]	Displays/hides proxy information. [ON], [OFF] Factory setting: [ON]
	[GPS]	Displays/hides GPS signal reception status. [ON], [OFF] Factory setting: [OFF]
	[CLIP NAME]	Displays/hides clip names. [ON], [OFF] Factory setting: [ON]
	[USER CLIP NAME (TYPE3)]	Displays/hides the user clip name when [REC SETTINGS] → [REC METADATA] → [USER CLIP NAME] is set to [TYPE3]. [ON], [OFF] Factory setting: [OFF]
	[REMOTE CTRL]	Displays/hides the ROP app control status. [ON], [OFF] Factory setting: [ON]
[MON OUT MARKER]	[MON OUT1 SW]	Displays/hides markers for the output from the <MON OUT1>. [ON], [OFF] Factory setting: [OFF]
	[MON OUT2 SW]	Displays/hides markers for the output from the <MON OUT2>. [ON], [OFF] Factory setting: [ON]
	[LCD SW]	Displays/hides markers for the control panel. [ON], [OFF] Factory setting: [ON]
	[PB MARKER SW]	Sets whether to superimpose markers to the playback images. The markers to superimpose are the same markers to superimpose to the camera video that is set in [MON OUT MARKER]. [ON], [OFF] Factory setting: [OFF]
	[MARKER & CHAR LVL]	Sets the frame marker and character luminance. Enabled for [FRAME MARK] only when [FRAME COLOR] is set to [WHITE]. [50%] - [100%] (10% step) Factory setting: [70%]
	[CENTER MARKER]	Controls the center mark. [1]: + (large) [2]: Open center (large) [3]: + (medium) [4]: Open center (medium) [5]: + (small) [6]: Open center (small) [7]: + (very small) [OFF]: Does not display. Factory setting: [1]
	[SAFETY MARKER]	Selects the type of frame for the safety zone marker. [1]: Box [2]: Corners [OFF]: Does not display. Factory setting: [OFF]
	[SAFETY AREA]	Sets the size of the safety zone marker. [80%] - [100%] (1% step, fixed aspect ratio) Factory setting: [90%]
	[FRAME MARK]	Enables/disables frame marker. [ON], [OFF] Factory setting: [OFF]
	[FRAME SIG]	Sets frame marker aspect ratio. [1.33:1], [1.44:1], [1.56:1], [1.78:1], [1.85:1], [2.00:1], [2.201:1], [2.35:1], [2.39:1] Factory setting: [2.39:1]
	[FRAME COLOR]	Sets the color of the frame marker. [WHITE], [BLACK], [RED], [GREEN], [BLUE], [YELLOW] Factory setting: [WHITE]
	[FRAME LEVEL]	Sets the level of the outside of the frame marker. [0%] - [100%] (10% step) Factory setting: [100%]
	[USER BOX]	Displays/hides the user box. [ON], [OFF] Factory setting: [OFF]
	[USER BOX WIDTH]	Sets the width of the user box. [1] - [100] Factory setting: [13]
	[USER BOX HEIGHT]	Sets the height of the user box. [1] - [100] Factory setting: [13]
	[USER BOX H POS]	Sets the horizontal position of the center of the user box. [−50] - [50] Factory setting: [0]
	[USER BOX V POS]	Sets the vertical position of the center of the user box. [−50] - [50] Factory setting: [0]
[VF INDICATOR]	[INDICATOR SW]	Sets whether to display items that will be set by [INDICATOR] in the output from the <VF> terminal and <VF SDI> terminal. [ON]: Items are individually displayed/hidden. [OFF]: Hides all. Factory setting: [ON]
	[SYSTEM PIXEL]	Displays/hides system pixels. [ON], [OFF] Factory setting: [ON]
	[SYSTEM FREQ]	Displays/hides system frequency. [ON], [OFF] Factory setting: [ON]
	[REC FORMAT]	Displays/hides recording format display. [ON], [OFF] Factory setting: [ON]
	[REC MODE]	Displays/hides the status for the interval recording or the pre-recording. [ON], [OFF] Factory setting: [ON]
	[VFR]	Displays/hides the variable frame rate status. [ON], [OFF] Factory setting: [ON]
	[FPS]	Displays/hides [FPS]. [ON], [OFF] Factory setting: [ON]
	[SHUTTER]	Displays/hides shutter speed. [ON], [OFF] Factory setting: [ON]
	[EI]	Displays/hides EXPOSURE INDEX. [ON], [OFF] Factory setting: [ON]
	[WHITE]	Displays/hides color temperature. [ON], [OFF] Factory setting: [ON]
	[IRIS]	Displays/hides iris value. [ON], [OFF] Factory setting: [ON]
	[FOCUS]	Displays/hides focus distance. [ON], [OFF] Factory setting: [ON]
	[ZOOM]	Displays/hides zoom value. [ON], [OFF] Factory setting: [ON]
	[FILTER]	Displays/hides the optical filter transmittance. [ON], [OFF] Factory setting: [ON]
	[EXTENDER]	Displays/hides the extender. [ON], [OFF] Factory setting: [ON]
	[Y GET]	Displays/hides brightness of Y GET. [ON], [OFF] Factory setting: [ON]
	[TC]	Displays/hides the time code, user bits, and duration counter displays. [TCG/TCR], [TCG], [OFF] Factory setting: [TCG/TCR]
	[P2 CARD REMAIN]	Displays/hides the display of the remaining recording free space of a P2 card. [ON], [OFF] Factory setting: [ON]
	[BATTERY REMAIN]	Displays/hides the estimated remaining battery charge level. [ON], [OFF] Factory setting: [ON]
	[PROXY]	Displays/hides proxy information. [ON], [OFF] Factory setting: [ON]
	[GPS]	Displays/hides GPS signal reception status. [ON], [OFF] Factory setting: [OFF]
	[REC TALLY]	Displays/hides the method of displaying the recording status. [RED]: The red tally lamp lights up. [GREEN]: The green tally lamp lights up. [CHAR]: The characters [REC] are displayed in the viewfinder. Factory setting: [RED]
	[CLIP NAME]	Displays/hides clip names. [ON], [OFF] Factory setting: [OFF]
	[USER CLIP NAME (TYPE3)]	Switches the display/hide of user clip name when [REC SETTINGS] → [REC METADATA] → [USER CLIP NAME] is set to [TYPE3]. [ON], [OFF] Factory setting: [OFF]
	[INDICATOR OUT SEL]	Selects the output destination of the item to set in the [INDICATOR] page. [VF], [VF SDI], [VF & VF SDI] Factory setting: [VF & VF SDI]
	[REMOTE CTRL]	Displays/hides the ROP app control status. [ON], [OFF] Factory setting: [ON]
[VF MARKER]	[MARKER SW]	Sets whether to display markers in the output from the <VF> terminal and <VF SDI> terminal. [ON], [OFF] Factory setting: [ON]
	[PB MARKER SW]	Sets whether to superimpose markers to the playback images. The markers to superimpose are the same markers to superimpose to the camera video that is set in [MON OUT MARKER]. [ON], [OFF] Factory setting: [OFF]
	[MARKER & CHAR LVL]	Sets the frame marker and character luminance. Enabled for [FRAME MARK]/[SURROUND VIEW] only when [FRAME COLOR]/[-- COLOR SEL] is set to [WHITE]. [50%], [60%], [70%] Factory setting: [50%]
	[CENTER MARKER]	Switches the center marker. [1]: + (large) [2]: Open center (large) [3]: + (medium) [4]: Open center (medium) [5]: + (small) [6]: Open center (small) [7]: + (very small) [OFF]: Does not display. Factory setting: [1]
	[SAFETY MARKER]	Selects the type of frame for the safety zone marker. [1]: Box [2]: Corners [OFF]: Does not display. Factory setting: [OFF]
	[SAFETY AREA]	Sets the size of the safety zone marker. [80] - [100%] (1% step, fixed aspect ratio) Factory setting: [90%]
	[FRAME MARK]	Enables/disables frame marker. [ON], [OFF] Factory setting: [OFF]
	[FRAME SIG]	Sets frame marker aspect ratio. [1.33:1], [1.44:1], [1.56:1], [1.78:1], [1.85:1], [2.00:1], [2.201:1], [2.35:1], [2.39:1] Factory setting: [2.39:1]
	[FRAME COLOR]	Sets the color of the frame marker. [WHITE], [BLACK], [RED], [GREEN], [BLUE], [YELLOW] Factory setting: [WHITE]
	[FRAME LEVEL]	Sets the level of the outside of the frame marker. [0%] - [100%] (10% step) Factory setting: [100%]
	[USER BOX]	Sets whether to display/hide the user box display. [ON], [OFF] Factory setting: [OFF]
	[USER BOX WIDTH]	Sets the width of the user box. [1] - [100] Factory setting: [13]
	[USER BOX HEIGHT]	Sets the height of the user box. [1] - [100] Factory setting: [13]
	[USER BOX H POS]	Sets the horizontal position of the center of the user box. [−50] - [50] Factory setting: [0]
	[USER BOX V POS]	Sets the vertical position of the center of the user box. [−50] - [50] Factory setting: [0]
	[MARKER OUT SEL]	Selects the output destination of the marker display. [VF], [VF SDI], [VF & VF SDI] Factory setting: [VF & VF SDI]
[VF FOCUS ASSIST]	[EXPAND SW]	Displays/hides the enlargement display function. [ON], [OFF] Factory setting: [OFF]
	[- POS]	Adjusts the source signal position in an enlarged display. [0] - [8] Factory setting: [4]
	[- VALUE]	Adjusts the enlargement factor. [x2], [x3], [x4] Factory setting: [x2]
	[- MODE]	Sets the enlargement display function mode. [10SEC], [HOLD], [UNTIL REC] Factory setting: [10SEC]
	[IN COLOR/SQ./MONO SW]	Displays/hides the advanced assist function (peaking and focus square). [ON], [OFF] Factory setting: [OFF]
	[- FOCUS IN COLOR SW]	Displays/hides the peaking function. [ON], [OFF] Factory setting: [OFF]
	[-- PEAKING VALUE]	Sets the peaking function mode. [LOW], [MID], [HIGH] Factory setting: [MID]
	[-- COLOR SEL]	Sets the peaking function color. [RED], [GREEN], [WHITE] Factory setting: [RED]
	[- FOCUS SQUARES SW]	Displays/hides the focus square function. [ON], [OFF] Factory setting: [OFF]
	[- MONO SW]	Enables/disables the monochromatic display function when [IN COLOR/SQ./MONO SW] is set to [ON]. [ON], [OFF] Factory setting: [OFF]
	[FOCUS BAR SW]	Enables/disables the focus bar display function. [ON], [OFF] Factory setting: [ON]
	[IN COLOR/SQ./MONO OUT SEL]	Selects the output destination of the advanced assist function. [VF], [VF SDI], [VF & VF SDI] Factory setting: [VF & VF SDI]
	[FOCUS BAR OUT SEL]	Selects the output destination of the focus bar display. [VF], [VF SDI], [VF & VF SDI] Factory setting: [VF & VF SDI]
[VF EI ASSIST]	[ZEBRA SW]	Sets whether to superimpose the zebra signal on the output from the <VF> terminal and <VF SDI> terminal. [ON], [OFF] Factory setting: [OFF]
	[ZEBRA1 DETECT]	Sets the detection level of zebra pattern 1. [0%] - [109%] Factory setting: [80%]
	[ZEBRA2 DETECT]	Sets the extraction level of zebra pattern 2. [0%] - [109%] Factory setting: [100%]
	[ZEBRA2 MODE]	Enables/disables zebra pattern 2 and selects [SPOT]. [ON], [SPOT], [OFF] Factory setting: [OFF]
	[ZEBRA OUT SEL]	Selects the output destination of the zebra display. [VF], [VF SDI], [VF & VF SDI] Factory setting: [VF & VF SDI]
	[WFM SW]	Displays/hides waveform monitor. [ON]/[OFF] Factory setting: [OFF]
	[- TYPE]	Sets the display format of the waveform monitor. [Y], [YGBR] Factory setting: [Y]
	[- TRANSPARENCE]	Sets the transparency of the waveform monitor display. [0%], [25%], [50%], [75%] Factory setting: [50%]
	[Y GET SW]	Enables/disables the Y GET display function. The user box function will not operate when [Y GET SW] is set to [ON]. [ON], [OFF] Factory setting: [OFF]
	[- UNIT]	Sets the [Y GET] display unit when [MAIN COLOR] is set to [V-Log]. [STOP], [%] Factory setting: [STOP]
	[- AREA SIZE]	Sets the size of area to detect with the Y GET display function. [S], [M], [L] Factory setting: [M]
	[FALSE COLOR SW]	Sets the display of the false color. [ON], [OFF] Factory setting: [OFF]
	[WFM OUT SEL]	Selects the output destination of the waveform monitor display. [VF], [VF SDI], [VF & VF SDI] Factory setting: [VF & VF SDI]
	[FALSE COLOR OUT SEL]	Selects the output destination of the false color display. [VF], [VF SDI], [VF & VF SDI] Factory setting: [VF & VF SDI]

Top of the page