Message

Screen display

Description

Behavior and cause

Camera image screen

[CANNOT PLAY.]

This is a clip that cannot be played back.

(When it cannot be played back due to difference of the system frequency, etc.)

An error has occurred during playback, and the playback has stopped.

A message is displayed.

  • Confirm if the system frequency of the clip is the same as the system frequency of the camera.

  • Check the clip.

[CANNOT DELETE.]

This is a clip that cannot be deleted.

A message is displayed.

  • Match the device and content versions.

[CANNOT RECORD. THE NUMBER OF CLIPS HAS EXCEEDED THE MAXIMUM LIMIT.]

The number of clips that can be recorded has reached the maximum.

A message is displayed.

  • Replace the memory card or delete unnecessary clips.

[CARD ERROR. PLEASE REFORMAT.]

Formatting of the memory card has failed.

A message is displayed.

  • Format it again.

[CANNOT RE-CONNECT.]

Clips cannot be re-connected due to the reasons such as selecting a clip that has not been recorded over multiple memory cards.

A message is displayed.

  • Check the selected clip.

[COPY IMPOSSIBLE. TOO LARGE CLIP CONTAINED.]

The P2 clip exceeding 4 GB cannot be copied to a memory card of 32 GB or less.

A message is displayed.

  • Copy to a memory card with the capacity exceeding 32 GB.

[CANNOT COPY TO SAME CARD.]

The clip recorded over multiple memory cards cannot be copied to a same memory card.

A message is displayed.

  • Copy to a memory card not containing a clip that is recorded over multiple memory cards.

[Repair failed.]

Repairing the clip where an error occurred has failed because the power was disconnected or the memory card was removed during recording.

Restoring of the management information has failed.

A message is displayed.

  • Check the memory card.

[REINSERT OR CHECK CARD.]

This memory card cannot be formatted.

A message is displayed.

  • Check the memory card.

[CANNOT PROTECT.]

This is a clip that cannot be protected.

A message is displayed.

  • Match the device and content versions.

[THE CLIP IS PROTECTED. PLEASE CANCEL PROTECTION.]

The clip is protected so it cannot be deleted.

A message is displayed.

  • Cancel the protect on the clip.

[CANNOT DELETE UNTIL TOP MENU IS DELETED. DELETE TOP MENU? (RECORDED DATA WILL NOT BE DELETED)]

The camera is trying to delete a clip on the memory card where the top menu has been created.

A message is displayed.

  • Delete the top menu.

[CANNOT RECORD UNTIL TOP MENU IS DELETED. DELETE TOP MENU? (RECORDED DATA WILL NOT BE DELETED)]

The memory card where the top menu was created has been inserted.

A message is displayed.

  • Delete the top menu.

[THUMBNAIL DATA ERROR IS DETECTED.]

An error occurred in the thumbnail information of the memory card.

A message is displayed.

  • Restoring of the management information is performed automatically after this.

[CANNOT RECORD - INCOMPATIBLE CONTROL DATA.]

The version of the management information on the memory card is not supported.

A message is displayed.

  • Match the device and content versions.

[CANNOT SET.]

This cannot be set.

A message is displayed.

  • Perform the setting after making it possible to set.

[THIS CLIP CANNOT BE COPIED.]

The clip cannot be copied.

A message is displayed.

  • Copy the clips other than the corresponding clip.

[CONTROL DATA ERROR HAS BEEN DETECTED. (SD CARD)]

An error occurred in the management information of the memory card.

A message is displayed.

  • Restoring of the management information is performed automatically after this.

[COPY FAILED. PLEASE CHECK THE CARD.]

The clip has failed to copy due to an error in the memory card.

A message is displayed.

  • Check the memory card.

[CANNOT COPY - THE NUMBER OF CLIPS HAS REACHED MAXIMUM.]

The number of clips that can be copied has reached the maximum.

A message is displayed.

  • Replace the memory card in the copy destination or delete unnecessary clips.

[CANNOT PLAY THIS CLIP ON THIS MODEL.]

This is a clip that cannot be played back with the camera.

A message is displayed.

  • Playback on a device that can playback.

[INVALID]

Operation is disabled.

A message is displayed.

  • Operate after the the operation becomes enabled.

[Cannot record - Playlist capacity is full.]

The camera tried to record on a memory card where the number of playlists for recording has reached the maximum.

A message is displayed.

  • Replace the memory card or delete unnecessary clips.

[Cannot copy - Playlist capacity is full.]

The camera tried to copy to a memory card where the number of playlists for recording has reached the maximum.

A message is displayed.

  • Replace the memory card or delete unnecessary clips.

[Exceeds capacity. Please reselect.]

The remaining recording capacity of the memory card for the copy destination is insufficient.

A message is displayed.

  • Select the clip to copy again, or secure enough space in the remaining recording capacity on the memory card for the copy destination.

[Check the destination media.]

An error has occurred on the memory card for the copy destination while copying.

A message is displayed.

  • Confirm the memory card for the copy destination.

[LOAD NG]

Loading of the scene file has failed.

A message is displayed.

  • Check the memory card.

[SAVE NG]

Writing of the scene file has failed.

A message is displayed.

  • Check the memory card.

[DISCONNECT USB CABLE.]

Due to an OS non-compatible error, five minutes has elapsed until the service mode connection is established.

A message is displayed.

  • Confirm if the OS in use is supported by the camera.

[CARD LOCKED.]

The camera tried to protect or delete a clip on a memory card that has been locked.

The camera tried to copy a clip to the memory card that has been locked.

A message is displayed.

  • Unlock the memory card.

[CANNOT SELECT MORE CLIPS.]

It has tried to select more than 99 clips.

A message is displayed.

  • Execute the process such as copying by every 99 clips.

[SELECT THE CLIP TO BE DELETED.]

It has tried to delete a clip without choosing any.

A message is displayed.

  • Select a clip to be deleted.

[SELECT THE CLIPS TO COPY.]

It has tried to copy a clip without choosing any.

A message is displayed.

  • Select a clip to be copied.

[SELECT THE CLIP TO RE-CONNECT.]

It has tried to re-connect without choosing any clip.

A message is displayed.

  • Select the clip to be re-connected.

[NO CARD.]

Copying was tried to be executed without inserting a memory card into card slot.

A message is displayed.

  • Insert a memory card into the card slot.

[REINSERT OR CHECK CARD <SLOT 1>]/[REINSERT OR CHECK CARD <SLOT 2>]/[REINSERT OR CHECK CARD <SLOT 3>]

It has tried to copy to an error card.

A message is displayed.

  • Check the memory card.

[CANNOT RECORD.]

Cannot be recorded.

A message is displayed.

  • Perform recording after making it possible.

[REC PAUSE INVALID]

The camera tried to stop the next recording before the previous recording finished writing to the memory card.

A message is displayed.

  • Stop recording after writing to the memory card is complete. Recording can be stopped after the message that is displayed disappears.

[WRITE PROTECTED]

The write-protected switch on the memory card is set to the Protect side or the LOCK side.

A message is displayed.

  • Insert a memory card with write access.

[ATW MODE]

The camera tried to execute auto white balance while auto tracking white balance function operated.

A message is displayed.

  • Cancel the auto tracking white balance function and execute auto white balance.

[AWB PRESET ****K]

The camera tried to execute auto white balance when the <WHITE BAL> switch is set to <PRST>.

A message is displayed.

  • Set the <WHITE BAL> switch to <A> or <B> and execute auto white balance.

[AWB UNABLE]

[S.GAIN MODE]

The camera tried to execute auto white balance while super gain function operated.

A message is displayed.

  • Cancel the super gain function and execute auto white balance.

[CHECK FILTER]

The <ND FILTER>/<CC FILTER> dial is not set correctly at power on.

The camera tried to execute auto white balance when the <CC FILTER> dial was not set correctly.

A message is displayed.

  • Correctly set the <ND FILTER>/<CC FILTER> dial.

  • Correctly set the <CC FILTER> dial and execute auto white balance.

[LOW LIGHT]

Brightness has dropped.

A message is displayed.

  • Adjust the brightness.