Configures the settings for the external output, the information to display in the LCD monitor or viewfinder and the output format.
[VIDEO OUT SEL]
Switches the external output destination of the audio file.
[SDI+HDMI]
Outputs from the <SDI OUT> terminal and the <HDMI> terminal.
[AV+HDMI]
Outputs from the <AV OUT> terminal and the <HDMI> terminal.
(Factory setting: [SDI+HDMI])
[SDI OUT]
[OUTPUT SW]
Enables/disables the output from the <SDI OUT> terminal.
[ON]
Outputs the video.
[OFF]
Does not output the video.
(Factory setting: [ON])
[OUT FORMAT]
Selects the signal to output from the <SDI OUT> terminal. The items that can be selected differ depending on the [SYSTEM] menu → [FREQUENCY]/[FILE FORMAT]/[REC FORMAT] setting.
[1920×1080p]
Outputs in 1920×1080p.
[1920×1080i]
Outputs in 1920×1080i.
[1920×1080PsF]
Outputs in 1920×1080PsF.
[1280×720p]
Outputs in 1280×720p.
[720×480i]
Outputs in 720×480i.
[720×576i]
Outputs in 720×576i.
(Factory setting: [1920×1080i])
[3G-SDI OUT]
Sets the format of the 3G SDI signal output from the <SDI OUT> terminal. Can be set when the 3G SDI signal is output.
[LEVEL-A]
Selects the LEVEL-A method.
[LEVEL-B]
Selects the LEVEL-B DL method.
(Factory setting: [LEVEL-B])
[SD-SDI EDH]
Sets whether to superimpose EDH when output from the <SDI OUT> terminal is the SD signal (480i and 576i).
[ON]
Superimposes.
[OFF]
Does not superimpose.
(Factory setting: [ON])
[SDI REC REMOTE]
Sets if the recording operation against the external equipment connected to the <SDI OUT> terminal (such as recorder) is to be controlled or not.
[ON]
Controls the recording operation of the external equipment.
[OFF]
Does not control the recording operation of the external equipment.
(Factory setting: [OFF])
[SDI OUT CHAR]
Sets whether to superimpose the character to the output from the <SDI OUT> terminal.
[ON]
Superimposes.
[OFF]
Does not superimpose.
(Factory setting: [OFF])
[SDI OUT ZEBRA]
Sets whether to superimpose the zebra signal to the output from the <SDI OUT> terminal. The settings of the zebra signal follow the zebra signal settings in the [VIDEO OUT/LCD/VF] menu → [EI ASSIST].
[ON]
Superimposes.
[OFF]
Does not superimpose.
(Factory setting: [OFF])
[SDI OUT HDR]
Sets the output image from the <SDI OUT> terminal.
[SDR]
Outputs in the standard dynamic range.
[HDR]
Outputs in the high dynamic range.
(Factory setting: [HDR])
[HDMI OUT]
[OUT FORMAT]
Selects the signal to output from the <HDMI> terminal. The items that can be selected differ depending on the [SYSTEM] menu → [FREQUENCY]/[FILE FORMAT]/[REC FORMAT] setting.
[3840×2160p]
Outputs in 3840×2160p (4:2:2/10-bit).
[3840×2160p(420/8bit)]
Outputs in 3840×2160p (4:2:0/8-bit).
[1920×1080p]
Outputs in 1920×1080p.
[1920×1080i]
Outputs in 1920×1080i.
[1280×720p]
Outputs in 1280×720p.
[720×480p]
Outputs in 720×480p.
[720×576p]
Outputs in 720×576p.
(Factory setting: [1920×1080p])
[HDMI TC OUT]
Sets if the time code information is output or not in the output from the <HDMI> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [OFF])
[HDMI REC REMOTE]
Sets if the recording operation against the external equipment connected to the <HDMI> terminal (such as recorder) is to be controlled or not. This can be set when [HDMI TC OUT] in [HDMI OUT] is enabled.
[ON]
Controls the recording operation of the external equipment.
[OFF]
Does not control the recording operation of the external equipment.
(Factory setting: [OFF])
[HDMI OUT CHAR]
Sets whether to superimpose the character to the output from the <HDMI> terminal.
[ON]
Superimposes.
[OFF]
Does not superimpose.
(Factory setting: [OFF])
[HDMI OUT ZEBRA]
Sets whether to superimpose the zebra signal to the output from the <HDMI> terminal. The settings of the zebra signal follow the zebra signal settings in the [VIDEO OUT/LCD/VF] menu → [EI ASSIST].
[ON]
Superimposes.
[OFF]
Does not superimpose.
(Factory setting: [OFF])
[HDMI OUT HDR]
Sets the output image from the <HDMI> terminal.
[SDR]
Outputs in the standard dynamic range.
[HDR]
Outputs in the high dynamic range.
(Factory setting: [HDR])
[AV OUT]
[OUTPUT SW]
Enables/disables the output from the <AV OUT> terminal.
[ON]
Outputs the video and audio.
[OFF]
Does not output the video and audio.
(Factory setting: [ON])
[AV OUT CHAR]
Sets whether to superimpose the character to the output from the <AV OUT> terminal.
[ON]
Superimposes.
[OFF]
Does not superimpose.
(Factory setting: [ON])
[AV OUT ZEBRA]
Sets whether to superimpose the zebra signal to the output from the <AV OUT> terminal. The settings of the zebra signal follow the settings in the [VIDEO OUT/LCD/VF] menu → [EI ASSIST] → [ZEBRA].
[ON]
Superimposes.
[OFF]
Does not superimpose.
(Factory setting: [OFF])
[SD DOWNCON MODE]
Sets the mode of the SD down converter output signal from an external output terminal.
[SIDE CROP]
Outputs an equal top and bottom width.
[LETTER BOX]
Outputs an equal right and left width.
[SQUEEZE]
Outputs by compressing in the horizontal direction to fit the screen.
(Factory setting: [LETTER BOX])
[LCD]
[BRIGHTNESS]
Adjusts the brightness of the LCD monitor.
The items that can be set are as follows.
[−15]…[15]
(Factory setting: [0])
[COLOR LEVEL]
Adjusts the color level of the LCD monitor.
The items that can be set are as follows.
[−15]…[15]
(Factory setting: [0])
[CONTRAST]
Adjusts the contrast of the LCD monitor.
The items that can be set are as follows.
[−30]…[30]
(Factory setting: [0])
[BACK LIGHT]
Adjusts the brightness of the LCD monitor backlight. [0] is the standard brightness.
The items that can be set are as follows.
[−1], [0], [1], [2]
(Factory setting: [0])
[SELF SHOOT]
Sets the display of the LCD monitor when mirror shooting is performed.
[NORMAL]
Does not invert the left and right sides.
[MIRROR]
Inverts the left and right sides.
(Factory setting: [MIRROR])
[VF]
[BRIGHTNESS]
Adjusts the brightness of the viewfinder.
The items that can be set are as follows.
[−15]…[15]
(Factory setting: [0])
[COLOR LEVEL]
Adjusts the color level of the viewfinder.
The items that can be set are as follows.
[−15]…[15]
(Factory setting: [0])
[CONTRAST]
Adjusts the contrast of the viewfinder.
The items that can be set are as follows.
[−30]…[30]
(Factory setting: [0])
[VF COLOR]
Sets whether to display video in the viewfinder in color or black and white.
[ON]
Displays in color.
[OFF]
Displays in black and white.
(Factory setting: [ON])
[EYE SENSOR]
Sets sensitivity of the eye sensor.
The items that can be set are as follows.
[HIGH], [LOW]
(Factory setting: [HIGH])
[LCD/VF HDR]
Sets the output image from the LCD monitor and viewfinder.
[SDR]
Outputs in the standard dynamic range.
[HDR]
Outputs in the high dynamic range.
(Factory setting: [HDR])
[INDICATOR]
Selects the indicator to display in the output image.
[FULL AUTO]
Displays/hides the status when the <AUTO/MANUAL> switch is at <AUTO>.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SLOT1/2 STATUS]
Displays/hides the status of the card slot and remaining recording capacity.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[2 SLOTS FUNC.]
Displays/hides the setting in the [RECORDING] menu → [2 SLOTS FUNC.].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[STREAMING]
Displays/hides the streaming status.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[NETWORK]
Displays/hides the wireless LAN and wired LAN connection status.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[BATTERY REMAIN]
Displays/hides the power status.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[REC FORMAT]
Displays/hides the recording format settings.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[FRAME RATE]
Displays/hides the settings in the [SCENE FILE] menu → [FRAME RATE].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[REC REMOTE]
Displays/hides the control status of the recording start and recording stop on the external equipment connected to the <SDI OUT> terminal and the <HDMI> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[REC MODE]
Displays/hides the status of the interval recording.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[FBC]
Toggles whether to display when the flash band compensation function is activated.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[HDR/DRS]
Toggles whether to display when the high dynamic range recording function or dynamic range stretcher function is enabled.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[O.I.S.]
Toggles whether to display when the optical image stabilizer function is enabled.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SCENE FILE]
Displays/hides scene file name.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[AREA]
Toggles whether to display when the area mode function or auto focus area width adjustment function is enabled.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[AUDIO LEVEL METER]
Displays/hides the audio level meter.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[GAIN]
Displays/hides the gain value.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[ND FILTER]
Displays/hides the ND filter transmittance.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SHUTTER]
Displays/hides the shutter speed.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[IRIS]
Displays/hides F value and auto iris control status.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[ZOOM/FOCUS]
Switches the unit of zoom and focus values.
[NUMBER]
Displays a position value for the zoom from [000] to [999] and focus from [00] to [99].
[mm/feet]
Displays the zoom in units of millimeters and the focus in units of feet.
[mm/m]
Displays the zoom in units of millimeters and the focus in units of meters.
[OFF]
Does not display either the zoom or focus.
(Factory setting: [NUMBER])
[WHITE BALANCE]
Displays/hides the color temperature.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[DATE/TIME]
Displays/hides the date and time.
The display for the year, month, and day follows the [DATE FORMAT] setting.
The date and time are not displayed when the time stamp function is enabled.
[OFF]
Does not display the date and time.
[DATE]
Displays only the date.
[TIME]
Displays only the time.
[DATE&TIME]
Displays the date and time.
(Factory setting: [OFF])
[SHOOTING MODE]
Displays/hides high-sensitivity mode.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[MULTI MANUAL]
Displays/hides the multi manual function.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[D.ZOOM]
Displays/hides the digital zoom ratio.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[IR REC]
Displays/hides the settings in the [CAMERA] menu → [SW MODE] → [IR REC].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[PLAYBACK STATUS]
Displays/hides the playback status.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[MARKER]
[CENTER MARKER]
Switch the type of the center marker.
[1]
+ (large)
[2]
Open center (large)
[3]
+ (small)
[4]
Open center (small)
[OFF]
Does not display.
(Factory setting: [1])
[SAFETY MARKER]
Selects the type of frame for the safety zone marker.
[1]
Box
[2]
Corners
[OFF]
Does not display.
(Factory setting: [2])
[SAFETY AREA]
Sets the size of the safety zone marker.
The items that can be set are as follows.
[80%]…[100%]
(Factory setting: [90%])
[FRAME MARKER]
Sets the aspect ratio of the frame marker. The frame marker is not displayed when [OFF] is selected.
Sets the focus assist method of the <FOCUS ASSIST> button.
[EXPAND]
Sets the enlarged display.
[PEAKING]
Sets the peaking display.
(Factory setting: [EXPAND])
[EXPAND MODE]
Sets the enlargement display function mode.
[10SEC]
Disables the enlarged display function after ten seconds have elapsed.
[HOLD]
Enables the enlarged display function until the <FOCUS ASSIST> button assigned to [EXPAND] or the USER button is pressed or the USER button icon is touched again.
[UNTIL REC]
Enables the enlarged display function until performing recording operation.
(Factory setting: [10SEC])
[EXPAND VALUE]
Adjusts the enlargement factor of the enlarged display function.
The items that can be set are as follows.
[×2], [×3], [×4]
(Factory setting: [×2])
[PEAKING LEVEL]
Sets the intensity of the peaking display.
The items that can be set are as follows.
[LOW], [MID], [HIGH]
(Factory setting: [MID])
[PEAKING COLOR]
Sets the color of the peaking display.
The items that can be set are as follows.
[RED], [GREEN], [WHITE]
(Factory setting: [RED])
[BLACK & WHITE]
Enables/disables the monochrome display.
[ON]
Enables the monochrome display.
[OFF]
Disables the monochrome display.
[DURING PEAKING]
Enables the monochrome display while the peaking display is enabled.
(Factory setting: [OFF])
[DETAIL]
Sets the intensity of the contour for the video to make it easier to focus.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[DETAIL LEVEL]
Sets the intensity of the contours.
The items that can be set are as follows.
[−3]…[3]
(Factory setting: [0])
[DETAIL FREQ.]
Adjusts the frequency of the contour highlights.
The items that can be set are as follows.
[HIGH], [LOW]
(Factory setting: [LOW])
[EI ASSIST]
[ZEBRA]
Sets whether to superimpose the zebra signal to the output.
[MOMENT]
Press the USER button to which [ZEBRA] is assigned or touch the USER button icon to superimpose the zebra signal for approximately five seconds.
[ON]
Always superimposes the zebra signal. Press the USER button to which [ZEBRA] is assigned in the [ON] settings or touch the USER button icon to set to [OFF].
[OFF]
Does not superimpose the zebra signal. Press the USER button to which [ZEBRA] is assigned in the [OFF] settings or touch the USER button icon to set to [ON].
(Factory setting: [OFF])
[ZEBRA1 DETECT]
Sets the detection level of zebra pattern 1.
The items that can be set are as follows.
[0%]…[109%]
(Factory setting: [80%])
[ZEBRA2 DETECT]
Sets the detection level of zebra pattern 2.
The items that can be set are as follows.
[0%]…[109%]
(Factory setting: [100%])
[ZEBRA2]
Enables/disables zebra pattern 2 and selects [SPOT].
The items that can be set are as follows.
[ON], [SPOT], [OFF]
(Factory setting: [OFF])
[WFM MODE]
Sets the display of the waveform monitor. Displaying of the waveform and the vector can be switched.
[WAVE]
Displays the waveform.
[VECTOR]
Displays the vector.
[WAVE/VECTOR]
Displays the waveform and the vector.
The waveform, vector or no display toggles in order each time the USER button to which [WFM] is assigned is pressed or the USER button icon is touched.
(Factory setting: [WAVE])
[WFM TRANSPARENCE]
Sets the transmittance of the waveform monitor.
The items that can be set are as follows.
[0%], [25%], [50%]
(Factory setting: [25%])
[LEVEL GAUGE]
[LEVEL GAUGE]
Displays/hides the level gauge.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[LEVEL GAUGE RESET]
Sets the horizontal and vertical reference value set by [LEVEL GAUGE SET] in the USER button to the factory setting.