Mode check display

[VIDEO OUT]

[VIDEO OUT SEL]

Displays the output destination of the video and audio with [SDI + HDMI]/[AV + HDMI].

[SDI OUT FORMAT]/[AV OUT FORMAT]

Displays as follows depending on the setting for the output destination of video and audio.

• When set to [SDI + HDMI]:

  The signal output from the <SDI OUT> terminal is displayed with [1920×1080p][1920×1080i]/[1920×1080PsF]/[1280×720p]/[720×480i]/[720×576i].

• When set to [AV + HDMI]:

  The signal output from the <AV OUT> terminal is displayed with [720×480i]/[720×576i].

[SDI OUT CHAR]/[AV OUT CHAR]

Displays as follows depending on the setting for the output destination of video and audio.

• When set to [SDI + HDMI]:

  Displays whether to superimpose the character to the output from the <SDI OUT> terminal with [ON]/[OFF].

• When set to [AV + HDMI]:

  Displays whether to superimpose the character to the output from the <AV OUT> terminal with [ON]/[OFF].

[HDMI OUT FORMAT]

The signal output from the <HDMI> terminal is displayed with [3840×2160p]/[3840×2160p(420/8bit)]/[1920×1080p]/[1920×1080i]/[1280×720p]/[720×480p]/[720×576p].

[HDMI OUT CHAR]

Displays whether to superimpose the character to the output from the <HDMI> terminal with [ON]/[OFF].

[SDI OUT]/[AV OUT]

Displays as follows depending on the setting for the output destination of video and audio.

• When set to [SDI + HDMI]:

  The output image from the <SDI OUT> terminal is displayed with [HDR]/[SDR].

• When set to [AV + HDMI]:

  The output image from the <AV OUT> terminal is displayed with [SDR].

[HDMI OUT]

The output image from the <HDMI> terminal is displayed with [HDR]/[SDR].

[LCD/VF]

Displays the output image from the LCD monitor and the viewfinder with [HDR]/[SDR].

—

Displays the status, remaining recording capacity, and the total capacity of the memory card inserted in the card slot.

It is not displayed when set to the [NETWORK] menu → [NETWORK FUNC] → [NDI|HX].

The status of the memory card that is displayed are following types.

• [NO CARD]: Memory card is not inserted.

• [UNSUPPORTED]: Memory card is not supported.

• [FORMAT ERROR]: Memory card cannot be used. (Format error)

• [PROTECTED]: It is write protected. (The write-protection switch of the memory card is set to the LOCK side)

• [NO REMAIN]: There is no remaining recording capacity.

• [NOT SDXC]: SDXC memory card is not inserted in the MOV recording.

• Cases other than above: The remaining recording capacity is displayed in 0% through 100%.

[TOTAL]

Displays the remaining recording capacity/total capacity of the memory cards in the card slot 1 and the card slot 2.

[SLOT1]

Displays the status and remaining recording capacity/total capacity of the memory card in card slot 1.

[SLOT2]

Displays the status and remaining recording capacity/total capacity of the memory card in card slot 2.

[AUDIO]

[AUDIO OUT]

Displays the audio channel and the format output from the <AV OUT> terminal, headphones terminal, and the built-in speaker with [CH1]/[CH2]/[CH1/2 STEREO]/[CH1/2 MIX].

[SELECT]

[CH1/2]

The audio to be recorded in each channel is displayed with [INT(L)]/[INT(R)]/[INPUT1]/[INPUT2].

[LINE/MIC]

[CH1/2]

The audio input signal of each channel is displayed with [LINE]/[MIC]/[MIC+48V].

Displays [---] when [INT(L)] or [INT(R)] is selected as the audio to be recorded.

[LEVEL]

[CH1/2]

Displays the adjustment method of the recording level of the audio for each channel with [AUTO]/[MANU].

[LIMITER]

[CH1/2]

Displays enable/disable of limiter for each channel with [ON]/[OFF].

Displays [---] when the adjustment method of the recording level of the audio is set to [AUTO].

[LOWCUT]

[CH1/2]

Displays enable/disable of low-cut filter for each channel with [ON]/[OFF].

[USER SW]

[1] - [7]

Displays the function assigned to <USER 1> through <USER 7> buttons.

[GAIN L]

Displays the gain value assigned to the <L> position of the <GAIN> switch.

[GAIN M]

Displays the gain value assigned to the <M> position of the <GAIN> switch.

[GAIN H]

Displays the gain value assigned to the <H> position of the <GAIN> switch.

[S.GAIN]

Displays the list of gain values assigned as a super gain.

[WHITE BAL A]

Displays the color temperature assigned to the <A> position of the <WHITE BAL> switch.

Displays [ATW] when the auto tracking white balance function is assigned.

[WHITE BAL B]

Displays the color temperature assigned to the <B> position of the <WHITE BAL> switch.

Displays [ATW] when the auto tracking white balance function is assigned.

[WHITE BAL PRST]

Displays the color temperature assigned to the <PRST> position of the <WHITE BAL> switch.

Displays [ATW] when the auto tracking white balance function is assigned.

Color temperature and [VAR] are displayed when [VAR] is assigned.

[DEVICE SEL]

Displays the device that connects an external equipment (computer, etc.) and the camera with [LAN]/[WLAN]/[OFF].

[NETWORK FUNC]

Displays the network function of the camera with [STREAMING]/[NDI|HX]/[OFF].

[STRM FORMAT]

Displays the streaming format.

It is not displayed when set to the [NETWORK] menu → [NETWORK FUNC] → [OFF].

[STRM DATA TYPE]

Displays the type of the streaming connection information.

It is not displayed when set to anything other than the [NETWORK] menu → [NETWORK FUNC] → [STREAMING].

[IP REMOTE]

Displays enable/disable of the IP remote function with [ENABLE]/[DISABLE].

[IP ADDRESS]

Displays the IP address in use.

It is not displayed when there is no IP address in use.