[PAINT]

[WHITE SHADING]

Enables/disables the white shading (saw-toothed waveform or parabolic waveform).

[OFF], [ON]

• Factory setting: [ON]

[FLARE]

Enables/disables flare.

[OFF], [ON]

• Factory setting: [ON]

[GAMMA]

Enables/disables gamma.

[OFF], [ON]

• Factory setting: [ON]

[BLACK GAMMA]

Enables/disables black gamma.

[OFF], [ON]

• Factory setting: [OFF]

[KNEE]

Enables/disables knee.

[OFF], [MANUAL], [AUTO]

• Factory setting: [MANUAL]

[WHITE CLIP]

Enables/disables white clips.

[OFF], [ON]

• Factory setting: [ON]

[DRS SW]

Enables/disables dynamic range stretcher.

[OFF], [ON]

It is displayed as [---] in the UHD mode/UHD CROP mode.

• Factory setting: [OFF]

[DETAIL]

Enables/disables the detail.

[OFF], [ON]

• Factory setting: [ON]

[SKIN TONE DETAIL]

Enables/disables the skin tone detail.

[OFF], [ON]

• Factory setting: [OFF]

[MATRIX]

Enables/disables matrix (linear matrix/12-axis color correction).

[OFF], [ON]

• Factory setting: [OFF]

[LINEAR MATRIX]

Enables/disables linear matrix.

[OFF], [ON]

• Factory setting: [OFF]

[COLOR CORRECT]

Enables/disables 12-axis color correction.

[OFF], [ON]

• Factory setting: [OFF]

[MASTER PEDESTAL]

Adjusts the black level of the master pedestal.

• Factory setting: [0]

[R PEDESTAL]

Sets the correction level of red to the master pedestal.

[−800] - [+800]

• Factory setting: [0]

[G PEDESTAL]

Sets the correction level of green to the master pedestal.

[−800] - [+800]

• Factory setting: [0]

[B PEDESTAL]

Sets the correction level of blue to the master pedestal.

[−800] - [+800]

• Factory setting: [0]

[PEDESTAL OFFSET]

Sets whether to maintain the Rch, Gch, and Bch pedestal levels after adjusting the automatic black balance.

[ON]: Maintains the values set in [R PEDESTAL], [G PEDESTAL], and [B PEDESTAL].

[OFF]: Sets [R PEDESTAL], [G PEDESTAL], and [B PEDESTAL] to [0].

• Factory setting: [OFF]

[MASTER PEDESTAL RANGE]

Sets the variable amount of the master pedestal.

[NORMAL]: Current variable amount

[WIDE]: Double of current variable amount

• Factory setting: [NORMAL]

[CHROMA LEVEL SWITCH]

Enables/disables the gain adjustment of chroma.

[OFF], [ON]

• Factory setting: [OFF]

[CHROMA LEVEL]

Sets the gain adjustment of chroma.

[−100%] - [+40%]

• Factory setting: [0%]

[COLOR TEMP PRE SWITCH]

Enables/disables the color temperature adjustment.

[OFF], [ON]

• Factory setting: [OFF]

[COLOR TEMP]

Sets the color temperature when [COLOR TEMP PRE SWITCH] is [ON].

• Factory setting: [3200K]

[R GAIN]

Sets the correction level of red to the color temperature.

[−400] - [+400]

• Factory setting: [0]

[B GAIN]

Sets the correction level of blue to the color temperature.

[−400] - [+400]

• Factory setting: [0]

[G AXIS]

Sets the correction level of green to the color temperature.

[−400] - [+400]

• Factory setting: [0]

[COLOR TEMP]

Sets the color temperature when the white balance is executed.

• Factory setting: [3200K]

[R GAIN]

Sets the correction level of red to the color temperature.

[−400] - [+400]

• Factory setting: [0]

[B GAIN]

Sets the correction level of blue to the color temperature.

[−400] - [+400]

• Factory setting: [0]

[G AXIS]

Sets the correction level of green to the color temperature.

[−400] - [+400]

• Factory setting: [0]

[R GAIN]

Sets the preset value of Rch gain.

This is not available when [COLOR TEMP PRE SWITCH] is set to [OFF].

[−1000] - [+1000]

• Factory setting: [0]

[B GAIN]

Sets the preset value of Bch gain.

This is not available when [COLOR TEMP PRE SWITCH] is set to [OFF].

[−1000] - [+1000]

• Factory setting: [0]

[R GAIN]

Sets the correction level of red to the gain.

[−1000] - [+1000]

• Factory setting: [0]

[B GAIN]

Sets the correction level of blue to the gain.

[−1000] - [+1000]

• Factory setting: [0]

[GAIN OFFSET]

Sets if the gain levels of Rch and Bch are maintained when the automatic white balance is adjusted.

[ON]: Maintains the values set with [R GAIN] and [B GAIN].

[OFF]: The values for [R GAIN] and [B GAIN] is set to [0].

• Factory setting: [OFF]

[CORRECT]

Enables/disables the white shading (saw-toothed waveform or parabolic waveform) correction.

[OFF], [ON]

• Factory setting: [ON]

[H SAW R]

Adjusts the white shading gain for Rch horizontally using a saw-toothed waveform.

[−100] - [+100]

• Factory setting: [0]

[H SAW G]

Adjusts the white shading gain for Gch horizontally using a saw-toothed waveform.

[−100] - [+100]

• Factory setting: [0]

[H SAW B]

Adjusts the white shading gain for Bch horizontally using a saw-toothed waveform.

[−100] - [+100]

• Factory setting: [0]

[H PARA R]

Adjusts the white shading gain for Rch horizontally using a parabolic waveform.

[−100] - [+100]

• Factory setting: [0]

[H PARA G]

Adjusts the white shading gain for Gch horizontally using a parabolic waveform.

[−100] - [+100]

• Factory setting: [0]

[H PARA B]

Adjusts the white shading gain for Bch horizontally using a parabolic waveform.

[−100] - [+100]

• Factory setting: [0]

[V SAW R]

Adjusts the white shading gain for Rch vertically using a saw-toothed waveform.

[−100] - [+100]

• Factory setting: [0]

[V SAW G]

Adjusts the white shading gain for Gch vertically using a saw-toothed waveform.

[−100] - [+100]

• Factory setting: [0]

[V SAW B]

Adjusts the white shading gain for Bch vertically using a saw-toothed waveform.

[−100] - [+100]

• Factory setting: [0]

[V PARA R]

Adjusts the white shading gain for Rch vertically using a parabolic waveform.

[−100] - [+100]

• Factory setting: [0]

[V PARA G]

Adjusts the white shading gain for Gch vertically using a parabolic waveform.

[−100] - [+100]

• Factory setting: [0]

Adjusts the white shading gain for Bch vertically using a parabolic waveform.

[−100] - [+100]

• Factory setting: [0]

[FLARE]

Enables/disables flare correction.

[OFF], [ON]

• Factory setting: [ON]

[MASTER FLARE]

Adjusts the master flare.

[−100] - [+100]

• Factory setting: [0]

[R FLARE]

Adjusts the Rch flare.

[−100] - [+100]

• Factory setting: [0]

[G FLARE]

Adjusts the Gch flare.

[−100] - [+100]

• Factory setting: [0]

Adjusts the Bch flare.

[−100] - [+100]

• Factory setting: [0]

[GAMMA]

Enables/disables gamma correction.

[OFF], [ON]

• Factory setting: [ON]

[GAMMA MODE SELECT]

Selects the type of gamma.

[HD], [FILMLIKE1], [FILMLIKE2], [FILMLIKE3], [FILM REC], [VIDEO REC]

• Factory setting: [HD]

[MASTER GAMMA]

Adjusts the gamma characteristic.

When [GAMMA MODE SELECT] is [HD]: [0.150] - [0.750] (0.0020 step)

When [GAMMA MODE SELECT] is [FILMLIKE1]/[FILMLIKE2]/[FILMLIKE3]: [0.3000] - [0.7500] (0.0025 step)

When [GAMMA MODE SELECT] is [FILE REC]/[VIDEO REC]: [0.150] - [0.750] (0.0020 step)

When [MAIN MENU] → [PAINT] → [DRS] → [DRS] is [ON]: [0.150] - [0.750] (0.0020 step)

• Factory setting: [0.450]

[R GAMMA]

Adjusts the gamma characteristic of red to the master gamma.

[−75] - [+75]

• Factory setting: [0]

[B GAMMA]

Adjusts the gamma characteristic of blue to the master gamma.

[−75] - [+75]

• Factory setting: [0]

[BLACK STRETCH LEVEL]

(Only when [FILM REC] is set) Sets the position of the gamma stretch.

[0%] - [30%]

• Factory setting: [0%]

[DYNAMIC LEVEL]

(Only when [FILM REC] is set) Sets dynamic range.

[200%], [300%], [400%], [500%]

• Factory setting: [500%]

[KNEE POINT]

(Only when [VIDEO REC] is set) Sets the knee point.

[30] - [90]

• Factory setting: [30]

[KNEE SLOPE]

(Only when [VIDEO REC] is set) Sets the knee slope.

[150%]/[200%]/[250%]/[300%]/[350%]/[400%]/[450%]/[500%]/[550%]/[600%]

• Factory setting: [150%]

[BLACK GAMMA]

Enables/disables black gamma.

This cannot be set when [MAIN MENU] → [PAINT] → [DRS] → [DRS] → [ON] is set.

[OFF], [ON]

• Factory setting: [OFF]

[MASTER BLACK GAMMA]

Adjusts the gamma characteristic adjacent to black.

[−48] - [+48]

• Factory setting: [0]

[R BLACK GAMMA]

Adjusts the gamma characteristic of red adjacent to black to the master gamma.

[−20] - [+20]

• Factory setting: [0]

[B BLACK GAMMA]

Adjusts the gamma characteristic of blue adjacent to black to the master gamma.

[−20] - [+20]

• Factory setting: [0]

—

Enables/disables the knee function.

[OFF], [MANUAL], [AUTO]

• Factory setting: [MANUAL]

[KNEE MASTER POINT]

Sets the knee point position.

[080.00%] - [110.00%] (0.25% step)

• Factory setting: [95.00%]

[KNEE R POINT]

Adjusts the knee point of red to [KNEE MASTER POINT].

[−25.00%] - [25.00%] (0.25% steps)

• Factory setting: [0.00%]

[KNEE B POINT]

Adjusts the knee point of blue to [KNEE MASTER POINT].

[−25.00%] - [25.00%] (0.25% steps)

• Factory setting: [0.00%]

[KNEE MASTER SLOPE]

Sets the knee slope.

[00] - [199]

• Factory setting: [130]

[KNEE R SLOPE]

Adjusts the knee slope of red to [KNEE MASTER SLOPE].

[−99] - [+99]

• Factory setting: [0]

[KNEE B SLOPE]

Adjusts the knee slope of blue to [KNEE MASTER SLOPE].

[−99] - [+99]

• Factory setting: [0]

[AUTO KNEE POINT]

Sets the break position of the auto knee.

• Factory setting: [95%]

[AUTO KNEE LEVEL]

Sets the maximum level of the auto knee.

• Factory setting: [108%]

[AUTO KNEE RESPONSE]

Sets the response speed of the auto knee. The smaller the setting value, the faster the response speed.

• Factory setting: [4]

[WHITE CLIP]

Enables/disables the white clip function.

[OFF], [ON]

• Factory setting: [ON]

[MASTER WHITE CLIP LEVEL]

Sets the white clip level.

[80%] - [109%]

• Factory setting: [109%]

[R WHITE CLIP LEVEL]

Adjusts red to [MASTER WHITE CLIP LEVEL].

[−15%] - [+15%]

• Factory setting: [0%]

[B WHITE CLIP LEVEL]

Adjusts blue to [MASTER WHITE CLIP LEVEL].

[−15%] - [+15%]

• Factory setting: [0%]

[HI-COLOR]

Sets whether to improve the color reproduction in high-luminance areas.

[OFF], [ON]

• Factory setting: [OFF]

[HI-COLOR LEVEL]

Sets the level of the mode that expands the color dynamic range.

[1] - [32]

• Factory setting: [32]

[DRS]

Enables/disables the dynamic range stretcher function. Set this to [ON] to automatically adjust the contrast.

[OFF], [ON]

It is displayed as [---] in the UHD mode/UHD CROP mode.

• Factory setting: [OFF]

[EFFECT DEPTH]

Sets the compression level of the high-luminance areas of the dynamic range stretcher function. Set a larger value to increase the compression level of the high-luminance areas.

[1] - [5]

It is displayed as [---] in the UHD mode/UHD CROP mode.

• Factory setting: [5]

[DETAIL]

Enables/disables all detail functions.

[OFF], [ON]

• Factory setting: [ON]

[MASTER DETAIL]

Sets the master detail.

[−31] - [+31]

• Factory setting: [0]

[H DETAIL LEVEL]

Sets the correction level of the horizontal detail.

[00] - [63]

• Factory setting: [20] (UHD mode/UHD CROP mode), [15] (HD mode)

[V DETAIL LEVEL]

Sets the correction level of the vertical detail.

[00] - [63]

• Factory setting: [32] (UHD mode/UHD CROP mode), [27] (HD mode)

[PEAK FREQUENCY]

Sets the peak frequency of the horizontal detail.

UHD mode/UHD CROP mode:

HD mode:

• Factory setting: [3] (UHD mode/UHD CROP mode), [18] (HD mode)

[V DETAIL FREQUENCY]

Sets the vertical detail frequency.

UHD mode/UHD CROP mode:

HD mode:

• Factory setting: [3] (UHD mode/UHD CROP mode), [18] (HD mode)

[CRISP]

Sets the detail signal noise removal level.

[00] - [63]

• Factory setting: [5] (UHD mode/UHD CROP mode), [0] (HD mode)

[DETAIL GAIN(+)]

Sets the detail level in the + (upward) direction.

It is displayed as [---] in the UHD mode/UHD CROP mode.

[−31] - [+31]

• Factory setting: [0]

[DETAIL GAIN(−)]

Sets the detail level in the − (downward) direction.

It is displayed as [---] in the UHD mode/UHD CROP mode.

[−31] - [+31]

• Factory setting: [0]

[DETAIL CLIP+]

Adjust the detail clip to reduce glare produced by an excess of details.

[00] - [63]

• Factory setting: [0]

[DETAIL CLIP−]

Adjusts the length of the undershoot of the detail edge component.

[00] - [63]

• Factory setting: [0]

[DETAIL SOURCE]

Sets the RGB signal component ratio to create the detail.

[(G+R)/2], [(G+B)/2], [(2G+B+R)/4], [(3G+R)/4], [R], [G]

It is displayed as [---] in the UHD mode/UHD CROP mode.

• Factory setting: [(G+R)/2]

[KNEE APERTURE LEVEL]

Adjusts the knee aperture level.

[00] - [39]

• Factory setting: [0] (UHD mode/UHD CROP mode), [5] (HD mode)

[LEVEL DEPENDENT SWITCH]

Enables/disables the function to remove details of dark areas.

[OFF], [ON]

• Factory setting: [ON] (UHD mode/UHD CROP mode), [OFF] (HD mode)

[LEVEL DEPENDENT]

Sets the level to remove details of dark areas.

[00] - [15]

• Factory setting: [8]

[DETAIL]

Enables/disables all detail functions.

[OFF], [ON]

• Factory setting: [ON]

[MASTER DETAIL]

Sets the master detail.

[−31] - [+31]

• Factory setting: [0]

[H DETAIL LEVEL]

Sets the correction level of the horizontal detail.

[00] - [63]

• Factory setting: [15]

[V DETAIL LEVEL]

Sets the correction level of the vertical detail.

[00] - [63]

• Factory setting: [15]

[PEAK FREQUENCY]

Sets the peak frequency of the horizontal detail.

[00] - [31]

• Factory setting: [10]

[V DETAIL FREQUENCY]

Sets the vertical detail frequency.

[00] - [31]

• Factory setting: [10]

[CRISP]

Sets the detail signal noise elimination level.

[00] - [63]

• Factory setting: [10]

[DETAIL GAIN(+)]

Sets the detail level in the + (upward) direction.

[−31] - [+31]

• Factory setting: [0]

[DETAIL GAIN(−)]

Sets the detail level in the − (downward) direction.

[−31] - [+31]

• Factory setting: [0]

[DETAIL CLIP+]

Adjust the detail clip to reduce glare produced by an excess of details.

[00] - [63]

• Factory setting: [0]

[DETAIL CLIP−]

Adjusts the length of the undershoot of the detail edge component.

[00] - [63]

• Factory setting: [0]

[DETAIL SOURCE]

Sets the RGB signal component ratio to create the detail.

[(G+R)/2], [(G+B)/2], [(2G+B+R)/4], [(3G+R)/4], [R], [G]

• Factory setting: [(G+R)/2]

[KNEE APERTURE LEVEL]

Adjusts the knee aperture level.

[00] - [39]

• Factory setting: [00]

[LEVEL DEPENDENT SWITCH]

Enables/disables the function to eliminate the detail in the dark areas.

[OFF], [ON]

• Factory setting: [OFF]

[LEVEL DEPENDENT]

Sets the level to eliminate the detail in the dark areas.

[00] - [15]

• Factory setting: [8]

[SKIN TONE DETAIL]

Enables/disables the skin tone detail function.

[OFF], [ON]

• Factory setting: [OFF]

—

Selects whether to automatically obtain the color saturation and hue information from the cursor position.

[NO], [YES]

[MEMORY SELECT]

Selects the skin tone table of the subject to apply the skin tone table to.

[A], [B], [C]

• Factory setting: [A]

[CURSOR]

Shows/hides the box cursor in the center of the screen.

[OFF], [ON]

• Factory setting: [OFF]

[H POSITION]

Adjusts the horizontal position of the cursor.

[0%] - [100.00%] (0.25% steps)

• Factory setting: [50.00%]

[V POSITION]

Adjusts the vertical position of the cursor.

[0%] - [100.00%] (0.25% steps)

• Factory setting: [50.00%]

—

Enables/disables the zebra display.

[OFF], [ON]

• Factory setting: [OFF]

[ZEBRA EFFECT MEMORY]

Selects the table of the zebra display.

[A], [B], [C], [A+B], [A+C], [B+C], [A+B+C]

• Factory setting: [A+B+C]

[SKIN TONE EFFECT MEMORY]

Selects the skin tone table used to apply the skin tone detail.

[A], [B], [C], [A+B], [A+C], [B+C], [A+B+C]

• Factory setting: [A+B+C]

[SKIN TONE CRISP]

Adjusts the skin tone detail.

[−63] - [+63]

• Factory setting: [+63]

[I CENTER]

Sets the center position on the I axis (the area where the skin tone effect is applied).

[0] - [255]

• Factory setting: [87] (UHD mode/UHD CROP mode), [18] (HD mode)

[I WIDTH]

Sets the width of the area where the skin tone effect is applied on the I axis with [I CENTER] being the center.

[0] - [255]

• Factory setting: [20] (UHD mode/UHD CROP mode), [8] (HD mode)

[Q WIDTH]

Sets the width of the area where the skin tone effect is applied on the Q axis with [I CENTER] being the center.

[0] - [255]

• Factory setting: [43]

Sets the phase of the area where the skin tone effect is applied with the Q axis being the reference.

[0] - [359]

• Factory setting: [90]

[MATRIX]

Enables/disables the matrix function.

[OFF], [ON]

• Factory setting: [OFF]

—

Enables/disables the linear matrix function.

[OFF], [ON]

• Factory setting: [OFF]

[LINEAR TABLE]

Selects the table for linear matrix.

[A], [B]

• Factory setting: [A]

—

Enables/disables the 12-axis color correction function.

[OFF], [ON]

• Factory setting: [OFF]

[COLOR CORRECT TABLE]

Selects the table for color correction.

[A], [B]

• Factory setting: [A]

[MATRIX (R-G)_N]

Adjusts the linear matrix between red and green.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX (R-G)_P]

Adjusts the linear matrix between red and green.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX (R-B)_N]

Adjusts the linear matrix between red and blue.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX (R-B)_P]

Adjusts the linear matrix between red and blue.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX (G-R)_N]

Adjusts the linear matrix between green and red.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX (G-R)_P]

Adjusts the linear matrix between green and red.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX (G-B)_N]

Adjusts the linear matrix between green and blue.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX (G-B)_P]

Adjusts the linear matrix between green and blue.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX (B-R)_N]

Adjusts the linear matrix between blue and red.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX (B-R)_P]

Adjusts the linear matrix between blue and red.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX (B-G)_N]

Adjusts the linear matrix between blue and green.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

Adjusts the linear matrix between blue and green.

This item is not available when [MATRIX] is set to [OFF].

[−31] - [+31]

• Factory setting: [0]

[MATRIX]

Enables/disables the matrix function.

[OFF], [ON]

• Factory setting: [OFF]

—

Enables/disables the linear matrix function.

[OFF], [ON]

• Factory setting: [OFF]

[LINEAR TABLE]

Selects the table for linear matrix.

[A], [B]

• Factory setting: [A]

—

Enables/disables the 12-axis color correction function.

[OFF], [ON]

• Factory setting: [OFF]

[COLOR CORRECT TABLE]

Selects the table for color correction.

[A], [B]

• Factory setting: [A]

[G SAT]

Adjusts green color saturation.

[−127] - [+126]

• Factory setting: [0]

[CY-G SAT]

Adjusts the color saturation between green and cyan.

[−127] - [+126]

• Factory setting: [0]

[CY SAT]

Adjusts cyan color saturation.

[−127] - [+126]

• Factory setting: [0]

[B-CY SAT]

Adjusts the color saturation between cyan and blue.

[−127] - [+126]

• Factory setting: [0]

[B SAT]

Adjusts blue color saturation.

[−127] - [+126]

• Factory setting: [0]

[MG-B SAT]

Adjusts the color saturation between blue and magenta.

[−127] - [+126]

• Factory setting: [0]

[MG_SAT]

Adjusts magenta color saturation.

[−127] - [+126]

• Factory setting: [0]

[R-MG SAT]

Adjusts the color saturation between magenta and red.

[−127] - [+126]

• Factory setting: [0]

[R SAT]

Adjusts red color saturation.

[−127] - [+126]

• Factory setting: [0]

[YL-R SAT]

Adjusts the color saturation between red and yellow.

[−127] - [+126]

• Factory setting: [0]

[YL SAT]

Adjusts yellow color saturation.

[−127] - [+126]

• Factory setting: [0]

[G-YL SAT]

Adjusts the color saturation between yellow and green.

[−127] - [+126]

• Factory setting: [0]

[G PHASE]

Adjusts green hue.

[−127] - [+127]

• Factory setting: [0]

[CY-G PHASE]

Adjusts the hue between green and cyan.

[−127] - [+127]

• Factory setting: [0]

[CY PHASE]

Adjusts cyan hue.

[−127] - [+127]

• Factory setting: [0]

[B-CY PHASE]

Adjusts the hue between cyan and blue.

[−127] - [+127]

• Factory setting: [0]

[B PHASE]

Adjusts blue hue.

[−127] - [+127]

• Factory setting: [0]

[MG-B PHASE]

Adjusts the hue between blue and magenta.

[−127] - [+127]

• Factory setting: [0]

[MG_PHASE]

Adjusts magenta hue.

[−127] - [+127]

• Factory setting: [0]

[R-MG PHASE]

Adjusts the hue between magenta and red.

[−127] - [+127]

• Factory setting: [0]

[R PHASE]

Adjusts red hue.

[−127] - [+127]

• Factory setting: [0]

[YL-R PHASE]

Adjusts the hue between red and yellow.

[−127] - [+127]

• Factory setting: [0]

[YL PHASE]

Adjusts yellow hue.

[−127] - [+127]

• Factory setting: [0]

[G-YL PHASE]

Adjusts the hue between yellow and green.

[−127] - [+127]

• Factory setting: [0]

[SKIN AREA SW]

Enables/disables the function to finely adjust the color of the skin tone area.

[OFF], [ON]

• Factory setting: [OFF]

[SKIN AREA TABLE]

Selects the table for the skin tone area.

[A], [B]

• Factory setting: [A]

[SKIN AREA HUE]

Finely adjusts the hue of the skin tone area.

[−127] - [+127]

• Factory setting: [0]

Finely adjusts the tone of the skin tone area.

[−127] - [+126]

• Factory setting: [0]

[DNR SW]

Enables/disables the noise reduction function.

[OFF], [ON]

• Factory setting: [ON]

[DNR LEVEL]

Sets the level for the noise reduction.

The larger the value, the stronger the noise reduction effect.

[1] - [5]

• Factory setting: [3]

[HAZE REDUCTION]

Enables/disables the haze elimination function.

• Factory setting: [OFF]

[HAZE REDUCTION LEVEL]

Sets the level of the haze elimination.

The larger the value, the stronger the haze elimination effect.

• Factory setting: [1]

[MODE]

Selects the operation mode.

[LOAD], [STORE]

• Factory setting: [LOAD]

[FILE NO.]

Selects a file number.

When [MODE] is [LOAD]: [OFF], [1] - [8]

When [MODE] is [STORE]: [1] - [8]

• Factory setting: [OFF]

[FILE NAME]

Enters a file name. (15 characters or less)

• Factory setting: [SCENE1]

[EXECUTE]

Selects whether to execute with the configured settings.

[NO], [YES]