[IN/OUT SELECT]

[HD-SDI 3G SDI]

Sets the output format for HD SDI 3G output.

• Factory setting: [LEVEL-A]

[SDI1 OUT FMT]

Sets the output format of the <HD SDI OUT 1> terminal.

When [FORMAT] is [2160/60p]:

When [FORMAT] is [2160/59.94p]:

When [FORMAT] is [2160/29.97p]:

When [FORMAT] is [2160/23.98p]:

When [FORMAT] is [2160/29.97PsF]:

When [FORMAT] is [2160/23.98PsF]:

When [FORMAT] is [2160/50p]:

When [FORMAT] is [2160/25p]:

When [FORMAT] is [2160/25PsF]:

• Factory setting: [1080/59.94p]

[HD-SDI1 CHAR]

Sets if the character is imposed to the output image of the <HD SDI OUT 1> terminal.

• Factory setting: [OFF]

[HD-SDI OUT ITEM]

Sets the content of the character superimposed to the output image from the <HD SDI OUT 1>/<HD SDI OUT 2> terminal.

[MENU ONLY]: Displays only on the menu.

[STATUS]: Displays all characters that are the same as displayed in the monitor.

• Factory setting: [MENU ONLY]

[HDR SW (SDI 1)]

Switches the HDR/SDR for the signal output from the <HD SDI OUT 1> terminal.

[ON]: HDR

[OFF]: SDR

• Factory setting: [ON]

[HDR SW (SDI 2)]

Switches the HDR/SDR for the signal output from the <HD SDI OUT 2> terminal.

[ON]: HDR

[OFF]: SDR

• Factory setting: [ON]

[HDR SW (LAN)]

Switches the HDR/SDR for the signal output from the <HD SDI OUT 2> terminal.

[ON]: HDR

[OFF]: SDR

• Factory setting: [ON]

[UHD-SDI S-LINK]

Switches the output signal when the 12G output board AK-UHD12G (optional) is installed.

[ON]: Outputs the 12G SDI signal.

[OFF]: Outputs the 3G SDI signal.

• Factory setting: [ON]

This is displayed only when the 12G output board AK-UHD12G (optional) is installed.

[UHD-SDI OUT TYPE]

Sets the output format of UHD.

• Factory setting: [SQUARE]

[UHD-SDI 3G SDI]

Sets the output format for UHD SDI 3G output.

• Factory setting: [LEVEL-A]

[LAN CHAR]

Sets if the character is superimposed to the output signal from the <LAN> terminal.

• Factory setting: [OFF]

[HD-SDI2 OUT SEL]

Sets the output image of the <HD SDI OUT 2> terminal during cropping.

• Factory setting: [FULL]

[LAN OUT SEL]

Sets the output image of the <LAN> terminal during cropping.

• Factory setting: [CROP]

[CROP OUT SEL]

Sets the crop output image during cropping.

• Factory setting: [YL]

[CROP MARKER SEL]

Sets the crop frame to display during cropping.

• Factory setting: [YL+G+MG]

[CROP ADJ SEL]

Sets the crop frame to adjust the position during cropping.

• Factory setting: [YL]

[CROP H POSITION]

Sets the horizontal position of crop during cropping.

[−50.00%] - [+50.00%] (0.25% steps)

• Factory setting: [0.00%]

[CROP V POSITION]

Sets the vertical position of crop during cropping.

[−50.00%] - [+50.00%] (0.25% steps)

• Factory setting: [0.00%]

[CAM ID SWITCH]

Sets the status display to superimpose in the main line signal.

[OFF]: Camera ID is not displayed.

[BAR]: Camera ID is displayed only when set to [BAR].

[ON]: Camera ID is constantly displayed.

• Factory setting: [OFF]

[CAM ID CHARACTER]

Sets the camera name.

[CAM ID POSI]

Sets the display position of the camera ID.

[0]: Top left

[1]: Top right

[2]: Bottom left

[3]: Bottom right

• Factory setting: [1]

[GEN-LOCK INPUT]

Sets if the synchronization signal input is input from BNC or from D-SUB.

• Factory setting: [BNC]

[H PHASE-COARSE]

Roughly adjusts the phase of horizontal synchronization.

[−5] - [+5]

• Factory setting: [0]

[H PHASE-FINE]

Finely adjusts the phase of horizontal synchronization.

[−100] - [+100]

• Factory setting: [0]

[PROTCOL]

[PROTCOL]

Sets the type of the protocol.

[1]: Information camera communication protocol (EIA422)

[2]: Information camera communication protocol (EIA232)

[3]: Compatible personal computer control protocol (EIA422)

[4]: Compatible personal computer control protocol (EIA232)

• Factory setting: [3]