Selecting video output

The video output method can be selected.

Video output can be selected, for example, in the setting menus and SmartUI.

The setting of the <SDI OUT2/IN> terminal can be switched using the main menu → [IN/OUT SEL] → [SDI OUT2/IN SEL]. The setting of the <GL IN/VIDEO OUT> terminal can be switched using the main menu → [IN/OUT SEL] → [GL IN/VIDEO OUT SEL].

Setting item	Description of settings
[SDI2] ([SET02:MON OUT SELECT] screen of SmartUI)	Select the SDI output signal format from the <SDI OUT2/IN> terminal. The output signal format from the <HDMI> terminal is determined linked to this when the main menu → [IN/OUT SEL] → [HDMI OUT SIGNAL] is set to [MON].
[SETUP] (Main menu → [SYSTEM MODE])	Select the setup level of the signal (composite) to output to the <GL IN/VIDEO OUT> terminal. [0%]: 0% setup for both output and recording [7.5%A]: 7.5% setup for output only (recording 0%) The [SETUP] menu setting is valid also at playback.
[D.CON] ([SET02:MON OUT SELECT] screen of SmartUI)	Select the screen type at down-conversion output (composite and SD SDI output) in the HD mode (1080P, 1080i, 720P).

Setting item

Description of settings

[SDI2]

([SET02:MON OUT SELECT] screen of SmartUI)

Select the SDI output signal format from the <SDI OUT2/IN> terminal.

The output signal format from the <HDMI> terminal is determined linked to this when the main menu → [IN/OUT SEL] → [HDMI OUT SIGNAL] is set to [MON].

[SETUP] (Main menu → [SYSTEM MODE])

Select the setup level of the signal (composite) to output to the <GL IN/VIDEO OUT> terminal.

[0%]: 0% setup for both output and recording
[7.5%A]: 7.5% setup for output only (recording 0%)

The [SETUP] menu setting is valid also at playback.

[D.CON]

([SET02:MON OUT SELECT] screen of SmartUI)

Select the screen type at down-conversion output (composite and SD SDI output) in the HD mode (1080P, 1080i, 720P).

Selecting video output from each terminal

Describes the status of the video output when [MON] is set in the main menu → [IN/OUT SEL] → [HDMI OUT SIGNAL].

[LINE&FREQ]	Monitor output setting ([SET02:MON OUT SELECT] screen of SmartUI) *¹		Video output
[LINE&FREQ]	[SDI2]	[HDMI]	<SDI OUT1> terminal	<SDI OUT2/IN> terminal	<HDMI> terminal	<GL IN/VIDEO OUT> terminal
[1080-59.94P]	[1080i]	[1080i]	1080/59.94P*²	1080/59.94i	1080/59.94i	480/59.94i
[1080-59.94P]	[480i]	[480P]	1080/59.94P*²	480/59.94i	480/59.94P	480/59.94i
[1080-59.94i]	[1080i]	[1080i]	1080/59.94i	1080/59.94i	1080/59.94i	480/59.94i
[1080-59.94i]	[480i]	[480P]	1080/59.94i	480/59.94i	480/59.94P	480/59.94i
[1080-23.98PsF]	[1080i]	[1080i]	1080/23.98PsF	1080/23.98PsF over 59.94i 2:3	1080/23.98PsF over 59.94i 2:3	480/23.98PsF over 59.94i 2:3
[1080-23.98PsF]	[480i]	[480P]	1080/23.98PsF	480/23.98PsF over 59.94i 2:3	480/23.98PsF over 59.94i 2:3	480/23.98PsF over 59.94i 2:3
[720-59.94P]	[720P]	[720P]	720/59.94P	720/59.94P	720/59.94P	480/59.94i
[720-59.94P]	[480i]	[480P]	720/59.94P	480/59.94i	480/59.94P	480/59.94i
[480-59.94i]	[480i]	[480P]	480/59.94i	480/59.94i	480/59.94P	480/59.94i
[1080-50P]	[1080i]	[1080i]	1080/50P*²	1080/50i	1080/50i	576/50i
[1080-50P]	[576i]	[576P]	1080/50P*²	576/50i	576/50P	576/50i
[1080-50i]	[1080i]	[1080i]	1080/50i	1080/50i	1080/50i	576/50i
[1080-50i]	[576i]	[576P]	1080/50i	576/50i	576/50P	576/50i
[720-50P]	[720P]	[720P]	720/50P	720/50P	720/50P	576/50i
[720-50P]	[576i]	[576P]	720/50P	576/50i	576/50P	576/50i
[576-50i]	[576i]	[576P]	576/50i	576/50i	576/50P	576/50i

[SDI2] and [HDMI] are interlocked.

1080/59.94P and 1080/50P can be output from only the <SDI OUT1> terminal.

Top of the page