[OUTPUT SETTINGS]

Sets the display content of the output video from the viewfinder and <VF SDI> terminal.

Item

Description of settings

[SDI OUT]

[P to PsF]

Sets the segment frame for the output from terminals <SDI OUT1> to <SDI OUT4>.

This is enabled only when both of the following items are set.

  • When [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [FREQUENCY] is set to [29.97p], [23.98p], or [25.00p].

  • When [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] → [MAIN PIXEL] is set to [1920×1080].

[ON], [OFF]

  • Factory setting: [OFF]

[3G-SDI OUT]

Sets the 3G SDI signal format to be output from terminals <SDI OUT1> to <SDI OUT4>.

[LEVEL-A]: Selects the LEVEL-A method.

[LEVEL-B]: Selects the LEVEL-B DL method.

  • Factory setting: [LEVEL-B]

[SDI REC REMOTE]

Sets whether to use the control function of recording operation for an external device (such as a recorder) connected to the <SDI OUT> terminal, the <MON OUT1> terminal, and the <MON OUT2> terminal. It can be output from the <MON OUT2> terminal only when [MON OUT2 SIGNAL SEL] is set to [MON OUT1].

[ON]: Controls the recording operation of the external device.

[OFF]: Does not control the recording operation of the external device.

  • Factory setting: [OFF]

[MON OUT]

[MON OUT FORMAT]

Select the signal output from the <MON OUT1> terminal and <MON OUT2> terminal.

1920×1080:

[1920 over **p], [1920 over **i], [1920/**PsF]

1080i:

[1080i]

720P:

[720p]

** represents the frequency of the output signal. The signal that can be selected is limited depending on the [SYSTEM MODE] setting. The setting value will automatically change when the [SYSTEM MODE] setting is changed.

  • Factory setting: [1920p over 60p]

[3G-SDI OUT]

Sets the 3G SDI signal format to be output from the <MON OUT1> terminal and <MON OUT2> terminal.

[LEVEL-A]: Selects the LEVEL-A method.

[LEVEL-B]: Selects the LEVEL-B DL method.

  • Factory setting: [LEVEL-B]

[MON OUT2 SIGNAL SEL]

Sets the output from the <MON OUT2> terminal.

[VF SDI (1080p)]: Selects the same output as the <VF SDI> terminal. The signal format will always be 1920×1080p.

[VF SDI (1080i)]: Selects the same output as the <VF SDI> terminal. The signal format will always be 1920×1080i.

[MON OUT1]: Selects the same output as the <MON OUT1> terminal.

  • Factory setting: [VF (1080p)]

[MON OUT1 STATUS]

Sets whether to show the status display on the output from the <MON OUT1> terminal.

[ON], [OFF]

  • Factory setting: [OFF]

[MON OUT2 STATUS]

Sets whether to show the status display on the output from the <MON OUT2> terminal.

[ON], [OFF]

  • Factory setting: [OFF]

[MENU DISP]

Sets whether to display [MENU] in the output from the <MON OUT1> terminal and <MON OUT2> terminal.

[ON], [OFF]

  • Factory setting: [ON]

[PLAY DISP & CTRL]

Sets whether to display the PLAY screen in the output from the <MON OUT1> terminal and the <MON OUT2> terminal.

[ON], [OFF]

  • Factory setting: [OFF]

[VF OUT]

[VF SDI OUT FORMAT]

Selects the signal to output from the <VF SDI> terminal.

[1080P], [1080i]

  • Factory setting: [1080P]

[PLAYBACK VF IMAGE]

Selects the image output from the <VF> terminal and the <VF SDI> terminal.

[PLAYBACK], [CAMERA]

  • Factory setting: [PLAYBACK]

[SMOOTH MODE]

Enables/disables the smooth mode (function which smoothens the viewfinder image when 24P and half shutter function is running).

[ON], [OFF]

  • Factory setting: [OFF]

[MON OUT INDICATOR]

[SYSTEM PIXEL]

Displays/hides system pixels.

[ON], [OFF]

  • Factory setting: [ON]

[SYSTEM FREQ]

Displays/hides system frequency.

[ON], [OFF]

  • Factory setting: [ON]

[REC FORMAT]

Displays/hides recording format display.

[ON], [OFF]

  • Factory setting: [ON]

[REC MODE]

Displays/hides the status for the interval recording or the pre-recording.

[ON], [OFF]

  • Factory setting: [ON]

[VFR]

Displays/hides the variable frame rate status.

[ON], [OFF]

  • Factory setting: [ON]

[FPS]

Displays/hides frame rate.

[ON], [OFF]

  • Factory setting: [ON]

[SHUTTER]

Displays/hides shutter speed.

[ON], [OFF]

  • Factory setting: [ON]

[EI]

Displays/hides EXPOSURE INDEX.

[ON], [OFF]

  • Factory setting: [ON]

[WHITE]

Displays/hides color temperature.

[ON], [OFF]

  • Factory setting: [ON]

[IRIS]

Displays/hides iris value.

[ON], [OFF]

  • Factory setting: [ON]

[FOCUS]

Displays/hides focus distance.

[ON], [OFF]

  • Factory setting: [ON]

[ZOOM]

Displays/hides zoom value.

[ON], [OFF]

  • Factory setting: [ON]

[FILTER]

Displays/hides the optical filter transmittance.

[ON], [OFF]

  • Factory setting: [ON]

[EXTENDER]

Displays/hides the extender.

[ON], [OFF]

  • Factory setting: [ON]

[Y GET]

Displays/hides brightness of Y GET.

[ON], [OFF]

  • Factory setting: [ON]

[TC]

Displays/hides the time code, user bits, and duration counter displays.

[TCG/TCR], [TCG], [OFF]

  • Factory setting: [TCG/TCR]

[P2 CARD REMAIN]

Displays/hides the display of the remaining recording free space of a P2 card.

[ON], [OFF]

  • Factory setting: [ON]

[BATTERY REMAIN]

Displays/hides the estimated remaining battery charge level.

[ON], [OFF]

  • Factory setting: [ON]

[PROXY]

Displays/hides proxy information.

[ON], [OFF]

  • Factory setting: [ON]

[GPS]

Displays/hides GPS signal reception status.

[ON], [OFF]

  • Factory setting: [OFF]

[CLIP NAME]

Displays/hides clip names.

[ON], [OFF]

  • Factory setting: [ON]

[USER CLIP NAME (TYPE3)]

Displays/hides the user clip name when [REC SETTINGS] → [REC METADATA] → [USER CLIP NAME] is set to [TYPE3].

[ON], [OFF]

  • Factory setting: [OFF]

[REMOTE CTRL]

Displays/hides the ROP app control status.

[ON], [OFF]

  • Factory setting: [ON]

[MON OUT MARKER]

[MON OUT1 SW]

Displays/hides markers for the output from the <MON OUT1>.

[ON], [OFF]

  • Factory setting: [OFF]

[MON OUT2 SW]

Displays/hides markers for the output from the <MON OUT2>.

[ON], [OFF]

  • Factory setting: [ON]

[LCD SW]

Displays/hides markers for the control panel.

[ON], [OFF]

  • Factory setting: [ON]

[PB MARKER SW]

Sets whether to superimpose markers to the playback images.

The markers to superimpose are the same markers to superimpose to the camera video that is set in [MON OUT MARKER].

[ON], [OFF]

  • Factory setting: [OFF]

[MARKER & CHAR LVL]

Sets the frame marker and character luminance.

Enabled for [FRAME MARK] only when [FRAME COLOR] is set to [WHITE].

[50%]…[100%] (10% step)

  • Factory setting: [70%]

[CENTER MARKER]

Controls the center mark.

[1]: + (large)

[2]: Open center (large)

[3]: + (medium)

[4]: Open center (medium)

[5]: + (small)

[6]: Open center (small)

[7]: + (very small)

[OFF]: Does not display.

  • Factory setting: [1]

[SAFETY MARKER]

Selects the type of frame for the safety zone marker.

[1]: Box

[2]: Corners

[OFF]: Does not display.

  • Factory setting: [OFF]

[SAFETY AREA]

Sets the size of the safety zone marker.

[80%] - [100%] (1% step, fixed aspect ratio)

  • Factory setting: [90%]

[FRAME MARK]

Enables/disables frame marker.

[ON], [OFF]

  • Factory setting: [OFF]

[FRAME SIG]

Sets frame marker aspect ratio.

[1.33:1], [1.44:1], [1.56:1], [1.78:1], [1.85:1], [2.00:1], [2.201:1], [2.35:1], [2.39:1]

  • Factory setting: [2.39:1]

[FRAME COLOR]

Sets the color of the frame marker.

[WHITE], [BLACK], [RED], [GREEN], [BLUE], [YELLOW]

  • Factory setting: [WHITE]

[FRAME LEVEL]

Sets the level of the outside of the frame marker.

[0%] - [100%] (10% step)

  • Factory setting: [100%]

[USER BOX]

Displays/hides the user box.

[ON], [OFF]

  • Factory setting: [OFF]

[USER BOX WIDTH]

Sets the width of the user box.

[1]…[100]

  • Factory setting: [13]

[USER BOX HEIGHT]

Sets the height of the user box.

[1]…[100]

  • Factory setting: [13]

[USER BOX H POS]

Sets the horizontal position of the center of the user box.

[−50]…[50]

  • Factory setting: [0]

[USER BOX V POS]

Sets the vertical position of the center of the user box.

[−50]…[50]

  • Factory setting: [0]

[VF INDICATOR]

[INDICATOR SW]

Sets whether to display items that will be set by [INDICATOR] in the output from the <VF> terminal and <VF SDI> terminal.

[ON]: Items are individually displayed/hidden.

[OFF]: Hides all.

  • Factory setting: [ON]

[SYSTEM PIXEL]

Displays/hides system pixels.

[ON], [OFF]

  • Factory setting: [ON]

[SYSTEM FREQ]

Displays/hides system frequency.

[ON], [OFF]

  • Factory setting: [ON]

[REC FORMAT]

Displays/hides recording format display.

[ON], [OFF]

  • Factory setting: [ON]

[REC MODE]

Displays/hides the status for the interval recording or the pre-recording.

[ON], [OFF]

  • Factory setting: [ON]

[VFR]

Displays/hides the variable frame rate status.

[ON], [OFF]

  • Factory setting: [ON]

[FPS]

Displays/hides [FPS].

[ON], [OFF]

  • Factory setting: [ON]

[SHUTTER]

Displays/hides shutter speed.

[ON], [OFF]

  • Factory setting: [ON]

[EI]

Displays/hides EXPOSURE INDEX.

[ON], [OFF]

  • Factory setting: [ON]

[WHITE]

Displays/hides color temperature.

[ON], [OFF]

  • Factory setting: [ON]

[IRIS]

Displays/hides iris value.

[ON], [OFF]

  • Factory setting: [ON]

[FOCUS]

Displays/hides focus distance.

[ON], [OFF]

  • Factory setting: [ON]

[ZOOM]

Displays/hides zoom value.

[ON], [OFF]

  • Factory setting: [ON]

[FILTER]

Displays/hides the optical filter transmittance.

[ON], [OFF]

  • Factory setting: [ON]

[EXTENDER]

Displays/hides the extender.

[ON], [OFF]

  • Factory setting: [ON]

[Y GET]

Displays/hides brightness of Y GET.

[ON], [OFF]

  • Factory setting: [ON]

[TC]

Displays/hides the time code, user bits, and duration counter displays.

[TCG/TCR], [TCG], [OFF]

  • Factory setting: [TCG/TCR]

[P2 CARD REMAIN]

Displays/hides the display of the remaining recording free space of a P2 card.

[ON], [OFF]

  • Factory setting: [ON]

[BATTERY REMAIN]

Displays/hides the estimated remaining battery charge level.

[ON], [OFF]

  • Factory setting: [ON]

[PROXY]

Displays/hides proxy information.

[ON], [OFF]

  • Factory setting: [ON]

[GPS]

Displays/hides GPS signal reception status.

[ON], [OFF]

  • Factory setting: [OFF]

[REC TALLY]

Displays/hides the method of displaying the recording status.

[RED]: The red tally lamp lights up.

[GREEN]: The green tally lamp lights up.

[CHAR]: The characters [REC] are displayed in the viewfinder.

  • Factory setting: [RED]

[CLIP NAME]

Displays/hides clip names.

[ON], [OFF]

  • Factory setting: [OFF]

[USER CLIP NAME (TYPE3)]

Switches the display/hide of user clip name when [REC SETTINGS] → [REC METADATA] → [USER CLIP NAME] is set to [TYPE3].

[ON], [OFF]

  • Factory setting: [OFF]

[INDICATOR OUT SEL]

Selects the output destination of the item to set in the [INDICATOR] page.

[VF], [VF SDI], [VF & VF SDI]

  • Factory setting: [VF & VF SDI]

[REMOTE CTRL]

Displays/hides the ROP app control status.

[ON], [OFF]

  • Factory setting: [ON]

[VF MARKER]

[MARKER SW]

Sets whether to display markers in the output from the <VF> terminal and <VF SDI> terminal.

[ON], [OFF]

  • Factory setting: [ON]

[PB MARKER SW]

Sets whether to superimpose markers to the playback images.

The markers to superimpose are the same markers to superimpose to the camera video that is set in [MON OUT MARKER].

[ON], [OFF]

  • Factory setting: [OFF]

[MARKER & CHAR LVL]

Sets the frame marker and character luminance.

Enabled for [FRAME MARK]/[SURROUND VIEW] only when [FRAME COLOR]/[-- COLOR SEL] is set to [WHITE].

[50%], [60%], [70%]

  • Factory setting: [50%]

[CENTER MARKER]

Switches the center marker.

[1]: + (large)

[2]: Open center (large)

[3]: + (medium)

[4]: Open center (medium)

[5]: + (small)

[6]: Open center (small)

[7]: + (very small)

[OFF]: Does not display.

  • Factory setting: [1]

[SAFETY MARKER]

Selects the type of frame for the safety zone marker.

[1]: Box

[2]: Corners

[OFF]: Does not display.

  • Factory setting: [OFF]

[SAFETY AREA]

Sets the size of the safety zone marker.

[80] - [100%] (1% step, fixed aspect ratio)

  • Factory setting: [90%]

[FRAME MARK]

Enables/disables frame marker.

[ON], [OFF]

  • Factory setting: [OFF]

[FRAME SIG]

Sets frame marker aspect ratio.

[1.33:1], [1.44:1], [1.56:1], [1.78:1], [1.85:1], [2.00:1], [2.201:1], [2.35:1], [2.39:1]

  • Factory setting: [2.39:1]

[FRAME COLOR]

Sets the color of the frame marker.

[WHITE], [BLACK], [RED], [GREEN], [BLUE], [YELLOW]

  • Factory setting: [WHITE]

[FRAME LEVEL]

Sets the level of the outside of the frame marker.

[0%] - [100%] (10% step)

  • Factory setting: [100%]

[USER BOX]

Sets whether to display/hide the user box display.

[ON], [OFF]

  • Factory setting: [OFF]

[USER BOX WIDTH]

Sets the width of the user box.

[1]…[100]

  • Factory setting: [13]

[USER BOX HEIGHT]

Sets the height of the user box.

[1]…[100]

  • Factory setting: [13]

[USER BOX H POS]

Sets the horizontal position of the center of the user box.

[−50]…[50]

  • Factory setting: [0]

[USER BOX V POS]

Sets the vertical position of the center of the user box.

[−50]…[50]

  • Factory setting: [0]

[MARKER OUT SEL]

Selects the output destination of the marker display.

[VF], [VF SDI], [VF & VF SDI]

  • Factory setting: [VF & VF SDI]

[VF FOCUS ASSIST]

[EXPAND SW]

Displays/hides the enlargement display function.

[ON], [OFF]

  • Factory setting: [OFF]

[- POS]

Adjusts the source signal position in an enlarged display.

[0]…[8]

  • Factory setting: [4]

[- VALUE]

Adjusts the enlargement factor.

[x2], [x3], [x4]

  • Factory setting: [x2]

[- MODE]

Sets the enlargement display function mode.

[10SEC], [HOLD], [UNTIL REC]

  • Factory setting: [10SEC]

[IN COLOR/SQ./MONO SW]

Displays/hides the advanced assist function (peaking and focus square).

[ON], [OFF]

  • Factory setting: [OFF]

[- FOCUS IN COLOR SW]

Displays/hides the peaking function.

[ON], [OFF]

  • Factory setting: [OFF]

[-- PEAKING VALUE]

Sets the peaking function mode.

[LOW], [MID], [HIGH]

  • Factory setting: [MID]

[-- COLOR SEL]

Sets the peaking function color.

[RED], [GREEN], [WHITE]

  • Factory setting: [RED]

[- FOCUS SQUARES SW]

Displays/hides the focus square function.

[ON], [OFF]

  • Factory setting: [OFF]

[- MONO SW]

Enables/disables the monochromatic display function when [IN COLOR/SQ./MONO SW] is set to [ON].

[ON], [OFF]

  • Factory setting: [OFF]

[FOCUS BAR SW]

Enables/disables the focus bar display function.

[ON], [OFF]

  • Factory setting: [ON]

[IN COLOR/SQ./MONO OUT SEL]

Selects the output destination of the advanced assist function.

[VF], [VF SDI], [VF & VF SDI]

  • Factory setting: [VF & VF SDI]

[FOCUS BAR OUT SEL]

Selects the output destination of the focus bar display.

[VF], [VF SDI], [VF & VF SDI]

  • Factory setting: [VF & VF SDI]

[VF EI ASSIST]

[ZEBRA SW]

Sets whether to superimpose the zebra signal on the output from the <VF> terminal and <VF SDI> terminal.

[ON], [OFF]

  • Factory setting: [OFF]

[ZEBRA1 DETECT]

Sets the detection level of zebra pattern 1.

[0%] - [109%]

  • Factory setting: [80%]

[ZEBRA2 DETECT]

Sets the extraction level of zebra pattern 2.

[0%] - [109%]

  • Factory setting: [100%]

[ZEBRA2 MODE]

Enables/disables zebra pattern 2 and selects [SPOT].

[ON], [SPOT], [OFF]

  • Factory setting: [OFF]

[ZEBRA OUT SEL]

Selects the output destination of the zebra display.

[VF], [VF SDI], [VF & VF SDI]

  • Factory setting: [VF & VF SDI]

[WFM SW]

Displays/hides waveform monitor.

[ON]/[OFF]

  • Factory setting: [OFF]

[- TYPE]

Sets the display format of the waveform monitor.

[Y], [YGBR]

  • Factory setting: [Y]

[- TRANSPARENCE]

Sets the transparency of the waveform monitor display.

[0%], [25%], [50%], [75%]

  • Factory setting: [50%]

[Y GET SW]

Enables/disables the Y GET display function.

The user box function will not operate when [Y GET SW] is set to [ON].

[ON], [OFF]

  • Factory setting: [OFF]

[- UNIT]

Sets the [Y GET] display unit when [MAIN COLOR] is set to [V-Log].

[STOP], [%]

  • Factory setting: [STOP]

[- AREA SIZE]

Sets the size of area to detect with the Y GET display function.

[S], [M], [L]

  • Factory setting: [M]

[FALSE COLOR SW]

Sets the display of the false color.

[ON], [OFF]

  • Factory setting: [OFF]

[WFM OUT SEL]

Selects the output destination of the waveform monitor display.

[VF], [VF SDI], [VF & VF SDI]

  • Factory setting: [VF & VF SDI]

[FALSE COLOR OUT SEL]

Selects the output destination of the false color display.

[VF], [VF SDI], [VF & VF SDI]

  • Factory setting: [VF & VF SDI]