[AUDIO SETUP]

Configure the settings regarding audio input/output.

Item

Description of settings

[INPUT SETTING]

[FRONT MIC POWER]

Selects the phantom power of the front microphone.

[ON], [OFF]

  • Factory setting: [ON]

[FRONT MIC LVL]

Sets the level of an external microphone connected to the <MIC IN> terminal. Enabled only when a microphone is connected.

[−40dB], [−50dB], [−60dB]

  • Factory setting: [−50dB]

[REAR MIC CH1 LVL]

Sets the level of an external microphone connected to the <AUDIO IN CH1/3> terminal. Enabled only when a microphone is connected.

[−50dB], [−60dB]

  • Factory setting: [−60dB]

[REAR MIC CH2 LVL]

Sets the level of an external microphone connected to the <AUDIO IN CH2/4> terminal. Enabled only when a microphone is connected.

[−50dB], [−60dB]

  • Factory setting: [−60dB]

[WIRELESS WARN]

Selects whether to display a warning when the reception status of the wireless microphone receiver is poor.

[ON], [OFF]

  • Factory setting: [OFF]

[WIRELESS TYPE]

Selects the type of wireless microphone receiver.

[SINGLE]: Selects a single channel type wireless microphone receiver.

[DUAL]: Selects a double channel type wireless microphone receiver.

  • Factory setting: [SINGLE]

[RECORDING CH SETTING]

[FRONT VR CH1]

Selects whether to enable the <F.AUDIO LEVEL> dial for input signals selected for audio channel 1.

[FRONT]: Enabled only when [FRONT] is selected.

[W.L.]: Enabled only when wireless microphone receiver is selected.

[REAR]: Enabled only when [REAR] is selected.

[ALL]: Enabled when any input is selected.

[OFF]: Disabled regardless of the input selected. Recording levels do not change even if the volume dial is turned.

  • Factory setting: [OFF]

[FRONT VR CH2]

Selects whether to enable the <F.AUDIO LEVEL> dial for input signals selected for audio channel 2.

[FRONT]: Enabled only when [FRONT] is selected.

[W.L.]: Enabled only when wireless microphone receiver is selected.

[REAR]: Enabled only when [REAR] is selected.

[ALL]: Enabled when any input is selected.

[OFF]: Disabled regardless of the input selected. Recording levels do not change even if the volume dial is turned.

  • Factory setting: [OFF]

[FRONT VR CH3]

Selects whether to enable the <F.AUDIO LEVEL> dial for input signals selected for audio channel 3.

[FRONT]: Enabled only when [FRONT] is selected.

[W.L.]: Enabled only when wireless microphone receiver is selected.

[REAR]: Enabled only when [REAR] is selected.

[ALL]: Enabled when any input is selected.

[OFF]: Disabled regardless of the input selected. Recording levels do not change even if the volume dial is turned.

  • Factory setting: [OFF]

[FRONT VR CH4]

Selects whether to enable the <F.AUDIO LEVEL> dial for input signals selected for audio channel 4.

[FRONT]: Enabled only when [FRONT] is selected.

[W.L.]: Enabled only when wireless microphone receiver is selected.

[REAR]: Enabled only when [REAR] is selected.

[ALL]: Enabled when any input is selected.

[OFF]: Disabled regardless of the input selected. Recording levels do not change even if the volume dial is turned.

  • Factory setting: [OFF]

[MIC LOWCUT CH1]

Enables/disables the lowcut filter for audio channel 1.

[ON], [OFF]

  • Factory setting: [OFF]

[MIC LOWCUT CH2]

Enables/disables the lowcut filter for audio channel 2.

[ON], [OFF]

  • Factory setting: [OFF]

[MIC LOWCUT CH3]

Enables/disables the lowcut filter for audio channel 3.

[ON], [OFF]

  • Factory setting: [OFF]

[MIC LOWCUT CH4]

Enables/disables the lowcut filter for audio channel 4.

[ON], [OFF]

  • Factory setting: [OFF]

[LIMITER CH1]

Enables/disables the limiter for audio channel 1.

[ON], [OFF]

  • Factory setting: [OFF]

[LIMITER CH2]

Enables/disables the limiter for audio channel 2.

[ON], [OFF]

  • Factory setting: [OFF]

[LIMITER CH3]

Enables/disables the limiter for audio channel 3.

[ON], [OFF]

  • Factory setting: [OFF]

[LIMITER CH4]

Enables/disables the limiter for audio channel 4.

[ON], [OFF]

  • Factory setting: [OFF]

[HEADROOM]

Sets the headroom (standard level).

[18dB], [20dB]

  • Factory setting: [20dB]

[OUTPUT SETTING]

[TEST TONE]

Outputs rated level 1 kHz tone signal according to the reference level.

The standard level varies depending on the setting of [HEADROOM].

[NORMAL]: Outputs the test tone to CH1/CH2/CH3/CH4 when the <OUTPUT>/<AUTO KNEE> selector switch is switched to <BARS> and audio channel 1 is set to [FRONT] at the [IN] item on the [AUD02:INPUT] screen of SmartUI.

[ALWAYS]: Always outputs the test tone to CH1/CH2/CH3/CH4 when the <OUTPUT>/<AUTO KNEE> selector switch is switched to <BARS>.

[CHSEL]: Outputs the test tone to the channel where the [IN] item on the [AUD02:INPUT] screen of SmartUI is set to [FRONT] when the <OUTPUT>/<AUTO KNEE> selector switch is switched to <BARS>. (Does not output to CH3/CH4.)

[OFF]: Does not output the test tone.

  • Factory setting: [NORMAL]