[SETUP] screen

[SET01:TC/UB]

Sets the time code or user bits.

On the [HOME] screen, press the <COUNTER> button and select TC to display the time code setting screen and select UB to display the user bits setting screen.

Time code settings screen:

To set the time code, press the </REW> button to change to the time code setting mode.
The setting values of each digit of the time code are from [0] to [9] (decimal).

Corresponding button	Setting details and setting value
</REW> button	[TCG] Starts and exits the time code setting mode. The time code setting is applied when the setting mode exits.	When the </REW> button is pressed, [SET] is displayed in black and white inversion, and the time code setting mode is set. When the </REW> button is pressed again, [SET] returns to the normal display, and the time code setting mode exits.
<STOP> button	[TC_MD] Selects the advance setting mode for the built-in time code generator.	[F-RUN] Use this function to advance the time code continuously, regardless of the P2 card recording operation. Set to this position to, for example, set the time code to the current time or externally lock the time code. [R-RUN] Use this function to advance the time code only during recording. A time code recorded normally will be continuously recorded. If a clip is deleted, or if the frame rate is set to [24PN] and the recording continues to a clip other than [24PN], continuous recording may fail. Factory setting: [F-RUN]
<FF/> button	[−] Decreases the setting value of the selected digit in the time code.
<PLAY/PAUSE> button	[+] Increases the setting value of the selected digit in the time code.
<COUNTER> button	[TC/UB] Switches to the user bits setting screen.
<RESET> button	[RST] Resets all time code setting values to 0.
<MONITOR SEL> button	[→] Moves the selected digit in the time code to the right. When the selected digit moves to the right edge, it moves back to the left edge.

User bits settings screen:

To set the user bits, press the </REW> button to change to the user bits setting mode.
The setting values of each digit of the user bits are from [0] to [F] (hexadecimal).

Corresponding button	Setting details and setting value
</REW> button	[UBG] Starts and exists the user bits setting mode. The user bits setting is applied when the setting mode exits.	When the </REW> button is pressed, [SET] is displayed in black and white inversion, and the user bits setting mode is set. When the </REW> button is pressed again, [SET] returns to the normal display, and the user bits setting mode exits.
<STOP> button	[TC_MD] Switches to the advance setting mode for the built-in time code generator. The setting contents are the same as when [TCG] is selected.
<FF/> button	[−] Decreases the setting value of the selected digit in the user bits.
<PLAY/PAUSE> button	[+] Increases the setting value of the selected digit in the user bits.
<COUNTER>	[TC/UB] Switches to the time code setting screen.
<RESET> button	[RST] Resets all user bits setting values to 0.
<MONITOR SEL> button	[→] Moves to the right of the selected digit in the user bits. When the selected digit moves to the right edge, it moves back to the left edge.

[SET02:MON OUT SELECT]

Sets the formats and aspects of video output from the <SDI OUT2/IN> terminal, the <HDMI> terminal, and the <GL IN/VIDEO OUT> terminal.

Corresponding button	Setting details and setting value
</REW> button	[SDI2] Sets the signal format type output from the <SDI OUT2/IN> terminal. With this setting, the signal format to be output from the <HDMI> terminal is also switched. When the main menu → [IN/OUT SEL] → [HDMI OUT SIGNAL] is set to [VF], the 1080i signal is output from the <HDMI> terminal, regardless of this setting. When [SDI IN] is selected, the signals 1080i, 720P, 480P, or 576P are output in accordance with the setting in the main menu → [SYSTEM MODE] → [LINE&FREQ].	[1080i] or [720P] (HDMI: [1080i] or [720P]) Displayed only in the HD mode. Outputs the SDI signal in accordance with the setting in the main menu → [SYSTEM MODE] → [LINE&FREQ]. The 1080i or 720P signal is also output from the <HDMI> terminal according to the [LINE&FREQ] setting. For [1080-59.94P] or [1080-50P], 1080/59.94i and 1080/50i is output from both the <SDI OUT2/IN> terminal and the <HDMI> terminal. For [1080-23.98PsF], the signal pulled down to 1080/59.94i is output from both <SDI OUT2/IN> and <HDMI> terminals. [480i] or [576i] (HDMI: [480P] or [576P]) The SDI signal of 480i or 576i is output. The 480P or 576P signal is output from the <HDMI> terminal.
<STOP> button	[D.CON] Sets the aspect for the down-conversion output signal in the HD mode. This item is not displayed in the SD mode.	[CROP] Side-crop mode (Crops the left and right edges.) [L.BOX] Letterbox mode (Adds black bands at the top and bottom of the image.) [SQU] Squeeze mode (Squeezes images horizontally.) Factory setting: [L.BOX]

Corresponding button

Setting details and setting value

</REW> button

[SDI2]

Sets the signal format type output from the <SDI OUT2/IN> terminal.

With this setting, the signal format to be output from the <HDMI> terminal is also switched.

When the main menu → [IN/OUT SEL] → [HDMI OUT SIGNAL] is set to [VF], the 1080i signal is output from the <HDMI> terminal, regardless of this setting.
When [SDI IN] is selected, the signals 1080i, 720P, 480P, or 576P are output in accordance with the setting in the main menu → [SYSTEM MODE] → [LINE&FREQ].

[1080i] or [720P] (HDMI: [1080i] or [720P])

Displayed only in the HD mode.

Outputs the SDI signal in accordance with the setting in the main menu → [SYSTEM MODE] → [LINE&FREQ].
The 1080i or 720P signal is also output from the <HDMI> terminal according to the [LINE&FREQ] setting.
For [1080-59.94P] or [1080-50P], 1080/59.94i and 1080/50i is output from both the <SDI OUT2/IN> terminal and the <HDMI> terminal.
For [1080-23.98PsF], the signal pulled down to 1080/59.94i is output from both <SDI OUT2/IN> and <HDMI> terminals.

[480i] or [576i] (HDMI: [480P] or [576P])

The SDI signal of 480i or 576i is output.
The 480P or 576P signal is output from the <HDMI> terminal.

<STOP> button

[D.CON]

Sets the aspect for the down-conversion output signal in the HD mode. This item is not displayed in the SD mode.

[CROP]

Side-crop mode (Crops the left and right edges.)

[L.BOX]

Letterbox mode (Adds black bands at the top and bottom of the image.)

[SQU]

Squeeze mode (Squeezes images horizontally.)

Factory setting: [L.BOX]

[SET03:MON OUT SETUP]

Sets the output setting of the <SDI OUT2/IN> terminal, the <HDMI> terminal, and the <GL IN/VIDEO OUT> terminal.

Corresponding button	Setting details and setting value
</REW> button	[OUT] Sets whether to output from the <SDI OUT2/IN> terminal, the <HDMI> terminal, and the <GL IN/VIDEO OUT> terminal.	[ON], [OFF] Factory setting: [ON]
</REW> button	When the remote control unit (AJ-RC10G), the extension control unit (AG-EC4G), or the remote operation panel (AK-HRP200G) is connected, the signal is always output from the <GL IN/VIDEO OUT> terminal regardless of this setting.
<STOP> button	[CHR] Specifies whether characters are superimposed over the output from the <SDI OUT2/IN> terminal, <HDMI> terminal, the <GL IN/VIDEO OUT> terminal, and the <REMOTE> terminal. The video signal output from the <SDI OUT1> terminal will be a candidate for selection when [MON CHAR] is selected in the main menu → [IN/OUT SEL] → [SDI OUT1 CHAR].	[ON], [OFF] Factory setting: [ON]
<STOP> button	This setting is disabled when the remote control unit (AJ-RC10G), the extension control unit (AG-EC4G), or the remote operation panel (AK-HRP200G) is connected, and the setting on the remote control unit, the extension control unit, or the remote operation panel will be applied.
<FF/> button	[ZBR] Specifies whether zebra pattern are superimposed over the output from the <SDI OUT2/IN> terminal, <HDMI> terminal, the <GL IN/VIDEO OUT> terminal, and the <REMOTE> terminal. This setting is not available when the setting menu on the viewfinder is open. The video signal output from the <SDI OUT1> terminal will be a candidate for selection when [MON ZEBRA] is selected in the main menu → [IN/OUT SEL] → [SDI OUT1 ZEBRA].	[ON], [OFF] Factory setting: [OFF]

[SET04:LCD]

Sets the display settings of SmartUI.

Corresponding button	Setting details and setting value
<FF/> button	[−] Decreases the setting value of the selected item. Press and hold this button to continuously decrease the setting value.
<PLAY/PAUSE> button	[+] Increases the setting value of the selected item. Press and hold this button to continuously increase the setting value.
<RESET> button	[RST] Resets the setting value of the selected item to its factory setting value.
<MONITOR SEL> button	[→] Moves the item selection to the right. When the item selection moves to the right edge, it moves back to the left edge.
[BACK LIGHT] Sets the luminance of SmartUI.	[1]…[5] Factory setting: [3]
[CONTRAST] Sets the contrast of SmartUI. The SmartUI screen may be hidden depending on the setting value. In such a case, press the <HOME> to return to the [HOME] screen and hold down the <LIGHT> and <RESET> buttons. The setting value of [CONTRAST] is reset to the factory setting.	[0]…[63] Factory setting: [33]

Corresponding button

Setting details and setting value

<FF/> button

[−]

Decreases the setting value of the selected item. Press and hold this button to continuously decrease the setting value.

<PLAY/PAUSE> button

[+]

Increases the setting value of the selected item. Press and hold this button to continuously increase the setting value.

<RESET> button

[RST]

Resets the setting value of the selected item to its factory setting value.

<MONITOR SEL> button

[→]

Moves the item selection to the right. When the item selection moves to the right edge, it moves back to the left edge.

[BACK LIGHT]

Sets the luminance of SmartUI.

[1]…[5]

Factory setting: [3]

[CONTRAST]

Sets the contrast of SmartUI.

The SmartUI screen may be hidden depending on the setting value.
In such a case, press the <HOME> to return to the [HOME] screen and hold down the <LIGHT> and <RESET> buttons. The setting value of [CONTRAST] is reset to the factory setting.

[0]…[63]

Factory setting: [33]

Top of the page