Mode check display

The camera settings and status can be displayed on the viewfinder.

Each time the <DISP/MODE CHK> switch on the camera is pushed towards the <CHK> side, the six screens are switched.

[STATUS] screen display → [FUNCTION] screen display → [AUDIO] screen display → [USER SW] screen display → [CAC INFO] screen display → [IN/OUT TERMINAL ASSIGN] screen display → no display

Each screen is displayed for approximately five seconds. Pushing the <DISP/MODE CHK> switch towards the <CHK> side while the screen is displayed moves to the next screen.

[FUNCTION] screen

Displays the video output status and information of the recording media.

Item

Description

[SDI OUT]

—

Displays the status of the signal output from the <SDI OUT1> terminal.

[TYPE]

Displays the format of the signal output from the <SDI OUT1> terminal by [HD-SDI]/[SD-SDI].

[CHAR]

Displays the superimposition status of characters selected in the main menu → [IN/OUT SEL] → [SDI OUT1 CHAR] by [ON]/[OFF].

[P2CARD STATUS]

—

Displays the status of the P2 card inserted in the card slot, remaining capacity, and total used capacity.

The statuses of cards to be displayed are as follows:

[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]

For details, refer to “P2 card access LEDs and status of P2 cards”.

[TOTAL P2/mP2]

Displays the remaining capacity/total capacity of slots 1 and 2 altogether.

[SLOT1]

Displays the status of the P2 card in slot 1 and remaining capacity/total capacity.

[SLOT2]

Displays the status of the P2 card in slot 2 and remaining capacity/total capacity.

[PROXY]

[MEDIA]

Displays the media selection status for proxy recording.

[P2]/[P2&SD]/[OFF]

[MODE]

Displays the setting status for proxy recording mode.

[AVC-G6 2CH MOV]/[SHQ 2CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV]

[PROXY ERROR]

Displays the operation error on the proxy module.

[NETWORK]

[NETWORK]

Displays the network to be used and its status.

[AUDIO] screen

Displays audio settings and the selection status of each recording channel.

Item

Description

[AUDIO]

[SAMPLE RES]

Displays the audio recording bits.

[A.IN]

[CH1/2/3/4]

Displays the input status of each channel.

[FRONT] (front), [REAR] (rear), [W.L.] (wireless)

[LEVEL]

[CH1/2/3/4]

Displays the recording level adjustment method currently selected on each channel.

  • [MANU]: Displayed when manual adjustment is set.

  • [AUTO]: Displayed when automatic adjustment is set.

Settings are performed in the SmartUI [AUD01:LEVEL] screen.

[F.VR]

[CH1/2/3/4]

Displays by [ON]/[OFF] whether the <F.AUDIO LEVEL> dial is enabled on the channel to which [VR] (manual adjustment by adjustment dial) is displayed in [LEVEL].

[LIMITER]

[CH1/2/3/4]

Displays the limiter settings of each channel.

[LOWCUT]

[CH1/2/3/4]

Displays the lowcut filter status of each channel.

[METER]

[CH1/2/3/4]

Displays the recording level of each channel.

[USER SW] screen

Displays the assignment status of each USER button. For details, refer to “Assigning functions to USER buttons”.

Item

Description

[OTHER ASSIGN]

[GAIN L]

Displays the gain value assigned to <L> of the <GAIN> switch.

[GAIN M]

Displays the gain value assigned to <M> of the <GAIN> switch.

[GAIN H]

Displays the gain value assigned to <H> of the <GAIN> switch.

[S.GAIN]

Enumerates and displays the gain value assigned as super gain.

[WHITE BAL A]

Displays the color temperature assigned to <A> of the <WHITE BAL> switch.

[WHITE BAL B]

Displays the color temperature assigned to <B> of the <WHITE BAL> switch.

[WHITE BAL PRE]

Displays the color temperature assigned to <PRST> of the <WHITE BAL> switch.

[USER SW]

[USER M]

Displays the assignment to the <USER MAIN> button.

[USER 1]

Displays the assignment to the <USER1> button.

[USER 2]

Displays the assignment to the <USER2> button.

[RET SW]

Displays the assignment to the <RET> button on the lens.

[CAC INFO] screen

Display the operation status or information of CAC.

Item

Description

[CAC CONT]

Displays the operation status of CAC.

  • [ON]: [ON] has been set in the main menu → [MAINTENANCE] → [CAC ADJ.] → [CAC CONTROL] and CAC is active.

  • [STOP]: [ON] has been set in the main menu → [MAINTENANCE] → [CAC ADJ.] → [CAC CONTROL], however, CAC operation stops under certain data or lens conditions.

  • [OFF]: [OFF] has been set in the main menu → [MAINTENANCE] → [CAC ADJ.] → [CAC CONTROL] and CAC is not active.

[CAC MODE]

Displays the operation mode of CAC.

  • [AUTO]: The CAC file is automatically selected.

[CONNECT LENS TYPE]

Displays the lens ID of the currently connected digital lens.

[SELECT FILE TITLE]

Displays the title and the file version of the CAC file currently used in the operation. The CAC file can be set in the main menu → [MAINTENANCE] → [CAC ADJ.].

[CAC WARNING]

Displays a warning when operation of CAC has stopped.

  • [CAC LENS DATA INVALID]: This is displayed, for example, when the response data from the lens is not supported.

  • [LENS INIT. NOT COMPLETED]: This is displayed, for example, when initialization of the lens cannot complete.

  • [CAC FILE DATA NOT FOUND]: Displayed when the chromatic aberration compensation function is set to [ON] and the chromatic aberration compensation data matching the connected lens.

[IN/OUT TERMINAL ASSIGN] screen

Display the settings of input and output terminals.

Item

Description

[GL IN/VIDEO OUT]

Displays the setting status of the <GL IN/VIDEO OUT> terminal set in the main menu → [IN/OUT SEL] → [GL IN/VIDEO OUT SEL].

[GL IN]: The terminal is set as [GENLOCK IN].

[VIDEO OUT]: The terminal is set as [VIDEO OUT].

[TC IN/OUT]

Displays the setting status of the <TC IN/OUT> terminal set in the main menu → [IN/OUT SEL] → [TC IN/OUT SEL].

[TC IN]: The terminal is set as [TC IN].

[TC OUT]: The terminal is set as [TC OUT].

[SDI OUT2/IN]

Displays the setting status of the <SDI OUT2/IN> terminal set in the main menu → [IN/OUT SEL] → [SDI OUT2/IN SEL].

[SDI OUT2]: The terminal is set as [SDI OUT2].

[SDI IN]: The terminal is set as [SDI IN].