Sets the display content or output format of the video.
[SDI OUT]
[OUTPUT SW]
Enables/disables the output from the <SDI OUT> terminal.
[ON]
Outputs the video.
[OFF]
Does not output the video.
(Factory setting: [ON])
[SIGNAL SEL]
Sets the output from the <SDI OUT> terminal.
[SDI]
Outputs the signal set in [OUT FORMAT] of [SDI OUT].
[LCD(1080p)]
Outputs the video displayed on the LCD monitor in 1920×1080p.
[LCD(1080i)]
Outputs the video displayed on the LCD monitor in 1920×1080i.
(Factory setting: [SDI])
[OUT FORMAT]
Selects the signal to be output from the <SDI OUT> terminal. The items that can be selected differ depending on the setting in the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [FREQUENCY]/[MAIN PIXEL].
[4096×2160p]
Outputs in 4096×2160p.
[3840×2160p]
Outputs in 3840×2160p.
[1920×1080p]
Outputs in 1920×1080p.
[1920×1080i]
Outputs in 1920×1080i.
[1920×1080PsF]
Outputs in 1920×1080PsF.
[1280×720p]
Outputs in 1280×720p.
(Factory setting: [1920×1080PsF])
[3G-SDI OUT]
Sets the format of the 3G SDI signal output from the <SDI OUT> terminal. Can be set when the 3G SDI signal is output.
[LEVEL-A]
Selects the LEVEL-A method.
[LEVEL-B]
Selects the LEVEL-B DL method.
(Factory setting: [LEVEL-B])
[SDI REC REMOTE]
Sets if the recording operation against the external equipment connected to the <SDI OUT> terminal (such as recorder) is to be controlled or not.
[ON]
Controls the recording operation of the external equipment.
[OFF]
Does not control the recording operation of the external equipment.
(Factory setting: [OFF])
[INDICATOR DISP]
Displays/hides the item set in [SDI/HDMI INDICATOR] for the output from the <SDI OUT> terminal.
[ON]
Displays the shutter speed, remaining battery level, etc. Content of display follows the setting in [SDI/HDMI INDICATOR].
[OFF]
Hides all.
(Factory setting: [ON])
[MARKER DISP]
Sets if the marker set in [SDI/HDMI MARKER] is displayed or not in the output from the <SDI OUT> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [OFF])
[MENU DISP]
Sets if the menu is displayed or not in the output from the <SDI OUT> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SDI OUT HDR]
Sets the output image from the <SDI OUT> terminal.
[SDR]
Outputs in the standard dynamic range.
[HDR]
Outputs in the high dynamic range.
(Factory setting: [HDR])
[HDMI OUT]
[SIGNAL SEL]
Sets the output from the <HDMI> terminal.
[HDMI]
Outputs the signal set in [OUT FORMAT] of [HDMI OUT].
[LCD(1080p)]
Outputs the video displayed on the LCD monitor in 1920×1080p.
(Factory setting: [HDMI])
[OUT FORMAT]
Selects the signal to be output from the <HDMI> terminal. The items that can be selected differ depending on the setting in the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [FREQUENCY]/[MAIN PIXEL].
[4096×2160p]
Outputs in 4096×2160p (4:2:2/10 bits).
[4096×2160p(420/8bit)]
Outputs in 4096×2160p (4:2:0/8 bits).
[3840×2160p]
Outputs in 3840×2160p (4:2:2/10 bits).
[3840×2160p(420/8bit)]
Outputs in 3840×2160p (4:2:0/8 bits).
[1920×1080p]
Outputs in 1920×1080p.
[1920×1080i]
Outputs in 1920×1080i.
[1280×720p]
Outputs in 1280×720p.
[720×480p]
Outputs in 720×480p.
[720×576p]
Outputs in 720×576p.
(Factory setting: [1920×1080p])
[HDMI TC OUT]
Sets if the time code information is output or not in the output from the <HDMI> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [OFF])
[HDMI REC REMOTE]
Sets if the recording operation against the external equipment connected to the <HDMI> terminal (such as recorder) is to be controlled or not. This can be set when [HDMI TC OUT] in [HDMI OUT] is enabled.
[ON]
Controls the recording operation of the external equipment.
[OFF]
Does not control the recording operation of the external equipment.
(Factory setting: [OFF])
[INDICATOR DISP]
Displays/hides the item set in [SDI/HDMI INDICATOR] for the output from the <HDMI> terminal.
[ON]
Displays the shutter speed, remaining battery level, etc. Content of display follows the setting in [SDI/HDMI INDICATOR].
[OFF]
Hides all.
(Factory setting: [ON])
[MARKER DISP]
Set if the marker set in [SDI/HDMI MARKER] is to be displayed or not in the output from the <HDMI> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [OFF])
[MENU DISP]
Sets if the menu is displayed or not in the output from the <HDMI> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[HDMI OUT HDR]
Sets the output image from the <HDMI> terminal.
[SDR]
Outputs in the standard dynamic range.
[HDR]
Outputs in the high dynamic range.
(Factory setting: [HDR])
[LCD HDR]
Sets the output image from the <LCD> terminal.
[SDR]
Outputs in the standard dynamic range.
[HDR]
Outputs in the high dynamic range.
(Factory setting: [HDR])
[SDI/HDMI INDICATOR]
Selects the indicator to display in the output image from the <SDI OUT> terminal or the output image from the <HDMI> terminal.
To display, set the [OUTPUT SETTINGS] menu → [SDI OUT] → [INDICATOR DISP] and the [OUTPUT SETTINGS] menu → [HDMI OUT] → [INDICATOR DISP] to [ON].
Displays/hides file name of the clip to record. Displays maximum of 8 characters from beginning.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[PIXEL/FREQ]
Displays/hides the number of recorded pixels and system frequency of the main recorder.
The display contents differ depending on the setting in the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [MAIN PIXEL] and [SENSOR MODE].
When [SENSOR MODE] is set to [S35 MIX 2.8K]: [2048 MIX] and [1920 MIX] are additionally displayed.
When [SENSOR MODE] is set to [4/3 CROP&MIX 2.2K]: [2048 CROP] and [1920 CROP] are additionally displayed.
When the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], the RAW output resolution and the system frequency set in [SDI RAW] are displayed.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[MAIN COLOR]
Displays/hides the color setting of the video to be recorded in the main recorder.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[REC FORMAT]
Displays/hides recording codec of the main recorder.
When the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], [SDI RAW] is displayed.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SLOT1/2 STATUS]
Displays/hides the status of the card slot and remaining recordable capacity.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[2 SLOTS FUNC.]
Displays/hides the setting in the [REC SETTINGS] menu → [2 SLOTS FUNC.].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[TC]
Displays/hides the time code, user bits, and duration counter. The display contents follow the setting in the [REC SETTINGS] menu → [TC] → [TC/UB/Dur.]. Displays the duration counter of TCR/UBR/playback clip during playback.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[BATTERY REMAIN]
Displays/hides the power status display.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[REC MODE]
Displays/hides the status of the interval recording.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[REC REMOTE]
Displays/hides the control status of the recording start and recording stop on the external equipment connected to the <SDI OUT> terminal and the <HDMI> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[AUDIO LEVEL METER]
Displays/hides the audio level meter.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[FPS]
Displays/hides the setting in the [CAMERA SETTINGS] menu → [FPS].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SHUTTER]
Displays/hides the shutter speed.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[EI]
Displays/hides EXPOSURE INDEX.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[WHITE]
Displays/hides color temperature.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[IRIS/ZOOM]
Displays/hides the lens aperture value and zoom value.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[FOCUS]
Switches the display unit for the focus value.
[feet]
Displays the focus value in feet/inch unit.
[m]
Displays the focus value in meter unit.
[OFF]
Does not display the focus value.
(Factory setting: [feet])
[ND FILTER]
Displays/hides the ND filter transmittance.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[E.I.S./D.ZOOM]
Displays/hides the setting in [E.I.S.] or [D.ZOOM].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[WLAN]
Displays/hides the connection status display of the wireless LAN.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[IR SHOOTING]
Displays/hides the setting in the [CAMERA SETTINGS] menu → [IR SHOOTING].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SPOT METER]
Displays/hides the spot meter.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[PLAYBACK STATUS]
Displays/hides the playback status.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SDI/HDMI MARKER]
[CENTER MARKER]
Switch the type of the center marker.
[1]
+ (large)
[2]
Open center (large)
[3]
+ (small)
[4]
Open center (small)
[OFF]
Does not display.
(Factory setting: [1])
[SAFETY MARKER]
Selects the type of frame for the safety zone marker.
[1]
Box
[2]
Corners
[OFF]
Does not display.
(Factory setting: [OFF])
[SAFETY AREA]
Sets the size of the safety zone marker.
The items that can be set are as follows.
[71.6%], [80%], [90%], [95%]
(Factory setting: [90%])
[FRAME MARKER]
Sets the aspect ratio of the frame marker. The frame marker is not displayed when [OFF] is selected.
Displays/hides the marker against the playback video output from the <SDI OUT> terminal and the <HDMI> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [OFF])
[LCD INDICATOR]
Selects the indicator displayed in the LCD monitor. For details of the displayed contents, refer to “Screen status display”.
[CLIP NAME]
Displays/hides file name of the clip to record. Displays maximum of 8 characters from beginning.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[PIXEL/FREQ]
Displays/hides the number of recorded pixels and system frequency of the main recorder.
The display contents differ depending on the setting in the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [MAIN PIXEL] and [SENSOR MODE].
When [SENSOR MODE] is set to [S35 MIX 2.8K]: [2048 MIX] and [1920 MIX] are additionally displayed.
When [SENSOR MODE] is set to [4/3 CROP&MIX 2.2K]: [2048 CROP] and [1920 CROP] are additionally displayed.
When the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], the RAW output resolution and the system frequency set in [SDI RAW] are displayed.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[MAIN COLOR]
Displays/hides the color setting of the video to be recorded in the main recorder.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[REC FORMAT]
Displays/hides recording codec of the main recorder.
When the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], [SDI RAW] is displayed.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SLOT1/2 STATUS]
Displays/hides the status of the card slot and remaining recordable capacity.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[2 SLOTS FUNC.]
Displays/hides the setting in the [REC SETTINGS] menu → [2 SLOTS FUNC.].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[TC]
Displays/hides the time code, user bits, and duration counter. The display contents follow the setting in the [REC SETTINGS] menu → [TC] → [TC/UB/Dur.]. Displays the duration counter of TCR/UBR/playback clip during playback.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[BATTERY REMAIN]
Displays/hides the power status display.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[REC MODE]
Displays/hides the status of the interval recording.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[REC REMOTE]
Displays/hides the control status of the recording start and recording stop on the external equipment connected to the <SDI OUT> terminal and the <HDMI> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[AUDIO LEVEL METER]
Displays/hides the audio level meter.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[FPS]
Displays/hides the setting in the [CAMERA SETTINGS] menu → [FPS].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SHUTTER]
Displays/hides the shutter speed.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[EI]
Displays/hides EXPOSURE INDEX.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[WHITE]
Displays/hides color temperature.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[IRIS/ZOOM]
Displays/hides the lens aperture value and zoom value.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[FOCUS]
Switches the display unit for the focus value.
[feet]
Displays the focus value in feet/inch unit.
[m]
Displays the focus value in meter unit.
[OFF]
Does not display the focus value.
(Factory setting: [feet])
[ND FILTER]
Displays/hides the ND filter transmittance.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[E.I.S./D.ZOOM]
Displays/hides the setting in [E.I.S.] or [D.ZOOM].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[WLAN]
Displays/hides the connection status display of the wireless LAN.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[IR SHOOTING]
Displays/hides the setting in the [CAMERA SETTINGS] menu → [IR SHOOTING].
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[SPOT METER]
Displays/hides the spot meter.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[PLAYBACK STATUS]
Displays/hides the playback status.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[LCD MARKER]
[CENTER MARKER]
Switch the type of the center marker.
[1]
+ (large)
[2]
Open center (large)
[3]
+ (small)
[4]
Open center (small)
[OFF]
Does not display.
(Factory setting: [1])
[SAFETY MARKER]
Selects the type of frame for the safety zone marker.
[1]
Box
[2]
Corners
[OFF]
Does not display.
(Factory setting: [OFF])
[SAFETY AREA]
Sets the size of the safety zone marker.
The items that can be set are as follows.
[71.6%], [80%], [90%], [95%]
(Factory setting: [90%])
[FRAME MARKER]
Sets the aspect ratio of the frame marker. The frame marker is not displayed when [OFF] is selected.
Displays/hides the marker against the playback video output from the <LCD> terminal
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [OFF])
[LCD FOCUS ASSIST]
[EXPAND MODE]
Sets the enlargement display function mode.
[10SEC]
Disables the enlarged display function after ten seconds have elapsed.
[HOLD]
The enlarged display function is enabled until the USER button assigned with [EXPAND] is pressed again.
[UNTIL REC]
Enables the enlarged display function until performing recording operation.
(Factory setting: [10SEC])
[EXPAND VALUE]
Adjusts the enlargement factor of the enlarged display function.
The items that can be set are as follows.
[×2], [×3], [×4]
(Factory setting: [×2])
[PEAK./SQUARES MODE]
Enables/disables the peaking function and focus square display (focus assist function).
[PEAKING]
Enables the peaking display.
[SQUARES]
Enables the focus square display.
[PEAK./SQUARES]
Enables peaking display and the focus square display. It will switch in the order of peaking display, focus square display, and no display every time the USER button with [PEAK./SQUARES F.A.] assigned is pressed.
(Factory setting: [SQUARES])
[PEAKING LEVEL]
Sets the intensity of the peaking display.
The items that can be set are as follows.
[LOW], [MID], [HIGH]
(Factory setting: [MID])
[PEAKING COLOR]
Sets the color of the peaking display.
The items that can be set are as follows.
[RED], [GREEN], [WHITE]
(Factory setting: [RED])
[BLACK & WHITE]
Enables/disables the monochrome display.
[ON]
Enables the monochrome display.
[OFF]
Disables the monochrome display.
[DURING PEAK./SQUARES]
The monochrome display is enabled while the peaking display and the focus square display is enabled.
(Factory setting: [OFF])
[OPEN IRIS MODE]
Sets the time for the open iris focus assist function is to operate. The open iris focus assist function is forced to cancel when the recording is started.
The items that can be set are as follows.
[10SEC], [30SEC]
(Factory setting: [10SEC])
[LCD EI ASSIST]
[ZEBRA]
Sets if the zebra signal is superimposed or not to the output from the <LCD> terminal.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [OFF])
[ZEBRA1 DETECT]
Sets the detection level of zebra pattern 1.
The items that can be set are as follows.
[0%]…[109%]
(Factory setting: [80%])
[ZEBRA2 DETECT]
Sets the detection level of zebra pattern 2.
The items that can be set are as follows.
[0%]…[109%]
(Factory setting: [100%])
[ZEBRA2]
Enables/disables zebra pattern 2 and selects [SPOT].
The items that can be set are as follows.
[ON], [SPOT], [OFF]
(Factory setting: [OFF])
[WFM MODE]
Sets the display of the waveform monitor. Displaying of the waveform and the vector can be switched.
[WAVE]
Displays the waveform.
[VECTOR]
Displays the vector.
[WAVE/VECTOR]
Displays the waveform and the vector.
It will switch in the order of waveform, vector, and no display every time the USER button with [WFM] assigned is pressed.
(Factory setting: [WAVE])
[WFM TRANSPARENCE]
Sets the transmittance of the waveform monitor.
The items that can be set are as follows.
[0%], [25%], [50%]
(Factory setting: [25%])
[SPOT METER UNIT]
Sets the display unit for the spot meter.
This is fixed to [%] when set to anything other than the [SYSTEM SETTINGS] menu → [COLOR SETTINGS] → [MAIN] → [V-Log].
The items that can be set are as follows.
[STOP], [%]
(Factory setting: [STOP])
[SPOT METER SIZE]
Sets the size of area to detect with the spot meter display function.
The items that can be set are as follows.
[S], [M], [L]
(Factory setting: [M])
[LCD LEVEL GAUGE]
[LEVEL GAUGE]
Displays/hides the level gauge.
The items that can be set are as follows.
[ON], [OFF]
(Factory setting: [ON])
[LEVEL GAUGE RESET]
Sets the horizontal and vertical reference value set by [LEVEL GAUGE SET] in the USER button to the factory setting.
The items that can be selected are as follows.
[YES], [NO]
[COLOR BARS]
[COLOR BARS TYPE]
Sets the color bar to be used.
[SMPTE]
Uses the color bars in SMPTE standard.
[FULL]
Uses the full color bars.
(Factory setting: [SMPTE])
[TEST TONE]
Sets if the audio test signal (tone signal of rating level 1 kHz) is output or not when the color bars are displayed.
The reference level varies depending on the setting in the [AUDIO SETTINGS] menu → [AUDIO CH SETTINGS] → [HEAD ROOM].