Clip name
Displays the clip name being recorded with maximum of eight characters from beginning.
System resolution/RAW output resolution
Displays the resolution set in the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [MAIN PIXEL]/[SENSOR MODE].
[4096×2160]
[3840×2160]
[2048×1080]
[1920×1080]
[1280×720]
[2048 MIX], [1920 MIX]: When [SENSOR MODE] is set to [S35 MIX 2.8K]
[2048 CROP], [1920 CROP]: When [SENSOR MODE] is set to [4/3 CROP&MIX 2.2K]
When the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], the RAW output resolution set in [SDI RAW] is displayed.
[S35 5.7K]
[CROP 4K]
[CROP&MIX 2K]
System frequency
Displays the frequency set in the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [FREQUENCY].
[23.98p]
[24.00p]
[25.00p]
[29.97p]
[50.00p]
[50.00i]
[59.94p]
[59.94i]
Color of the main recording
Displays the color setting set in the [SYSTEM SETTINGS] menu → [COLOR SETTINGS] → [MAIN].
[VLog]: V-Log
[SCN1]: SCENE1
[SCN2]: SCENE2
[SCN3]: SCENE3
[SCN4]: SCENE4
[SCN5]: SCENE5
Recording format
Displays the format set in the [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [MAIN CODEC]/[SDI RAW].
Recording status (card slot 1)
Displays the recording status of the SD card in the card slot 1.
: Not target for recording.
(flashing): Recognizing the SD card.
: The recording is stopped with the recording target SD card is inserted.
(flashing): Recognizing the SD card.
: Recording.
(Flashing red dot): Processing to stop the recording.
[P]: Recording is stopped with the pre-recording is enabled and the recording target SD card is inserted.
[P]: Pre-recording is enabled, and the SD card is not inserted in the card slot, or the SD card is not recognized.
(No display): It is in one of the following conditions.
The SD card is not inserted.
The SD card cannot be recognized.
The [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], and recording is stopped.
: It is in one of the following conditions.
The [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], and it is recording.
The tally lamp is instructed to illuminate in red via network.
Remaining recordable capacity and status of the SD card (card slot 1)
Displays the remaining recordable capacity of the SD card and status of the SD card in the card slot 1.
[0min] to [999min]: Remaining recordable capacity (999 minutes or more is displayed as [999min])
The display will flash when the remaining recordable capacity becomes two minutes or less.
During the simultaneous recording, the remaining recordable capacity to be able to perform simultaneous recording (the one with smaller remaining recordable capacity of the two SD cards) is displayed.
[WP]: Write protected (the write protection switch on the SD card is at the LOCK side)
[END]: No remaining recordable capacity (there is no remaining recordable capacity in the SD card)
[ERR]: The SD card that cannot be recorded is inserted (it is recognized, but cannot be used such as format error, other than SD card, etc.)
[!SDXC]: The SDXC memory card is not inserted for MOV recording
(No display): It is in one of the following conditions.
The SD card is not inserted.
The SD card cannot be recognized.
The [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].
Recording status (card slot 2)
Displays the recording status of the SD card in the card slot 2.
: Not target for recording.
(flashing): Recognizing the SD card.
: The recording is stopped with the recording target SD card is inserted.
(flashing): Recognizing the SD card.
: Recording.
(Flashing red dot): Processing to stop the recording.
[P]: Recording is stopped with the pre-recording is enabled and the recording target SD card is inserted.
[P]: Pre-recording is enabled, and the SD card is not inserted in the card slot, or the SD card is not recognized.
(No display): It is in one of the following conditions.
The SD card is not inserted.
The SD card cannot be recognized.
The [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].
Remaining recordable capacity and status of the SD card (card slot 2)
Displays the remaining recordable capacity of the SD card and status of the SD card in the card slot 2.
[0min] to [999min]: Remaining recordable capacity (999 minutes or more is displayed as [999min])
The display will flash when the remaining recordable capacity becomes two minutes or less.
During the simultaneous recording, the remaining recordable capacity to be able to perform simultaneous recording (the one with smaller remaining recordable capacity of the two SD cards) is displayed.
[WP]: Write protected (the write protection switch on the SD card is at the LOCK side)
[END]: No remaining recordable capacity (there is no remaining recordable capacity in the SD card)
[ERR]: The SD card that cannot be recorded is inserted (it is recognized, but cannot be used such as format error, other than SD card, etc.)
[!SDXC]: The SDXC memory card is not inserted for MOV recording
(No display): It is in one of the following conditions.
The SD card is not inserted.
The SD card cannot be recognized.
The [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].
Two-slot function
Displays the setting status of the recording function using two SD cards.
It is displayed with a slanted line if it is in a condition that cannot perform two-slot recording even if each function is enabled.
[RELAY]: When relay recording is enabled
[SIMUL]: When simultaneous recording is enabled
(No display): When it is standard recording
Time code
Displays the time code, user bits, and duration in accordance with the [REC SETTINGS] menu → [TC] → [TC/UB/Dur.] setting.
Power supply status
: Indicates the remaining battery level while powered with the battery. (The battery status display will change as → → → → while the remaining battery level gets lower. It will flash in red when the remaining battery level is zero)
: Displays when powered with the AC adaptor.
Audio level meter
Displays the volume.
Displays the reference level position set in the [AUDIO SETTINGS] menu → [AUDIO CH SETTINGS] → [HEAD ROOM] → [18dB]/[20dB] is blacked out. (Eighth from left when set to [20dB], ninth from left when set to [18dB])
Frame rate
Displays the frame rate.
Displays two places of decimals only when the frame rate is the same as the system frequency setting.
This is not displayed when the system frequency is 60i/50i.
Shutter speed
Displays the shutter speed.
Display of [sec] and [deg] can be switched with the [CAMERA SETTINGS] menu → [SHUTTER] → [MODE]. Displays in time (minutes) display when set to [sec], and in aperture angle when set to [deg].
Does not display when the shutter is disabled.
EXPOSURE INDEX
Displays the sensitivity of the video. Display of [ISO] and [dB] can be switched with the [CAMERA SETTINGS] menu → [EI] → [MODE].
Spot meter
Displays the brightness of the center in either [STOP] or [%] unit.
When [V-Log] is selected, [STOP] and [%] can be switched with the [OUTPUT SETTINGS] menu → [LCD EI ASSIST] → [SPOT METER UNIT]. When anything other than [V-Log] is selected, the display is fixed as [%].
Color temperature
Displays the selected color temperature.
Iris
Displays the F value. ([A] is displayed when auto iris is operating)
This is not displayed in the following cases.
Focus
Displays the focus value.
Display of the focus value follows the [OUTPUT SETTINGS] menu → [SDI/HDMI INDICATOR] → [FOCUS] and [OUTPUT SETTINGS] menu → [LCD INDICATOR] → [FOCUS] settings.
Displays in feet/inch unit when set to [feet].
Displays in meter unit when set to [m].
This is not displayed in the following cases.
Zoom
Displays the zoom distance in millimeter unit.
This is not displayed in the following cases.
ND filter
Displays the selected ND filter.
[ND:1.8]: Reduces the amount of light entering the MOS sensor to 1/64.
[ND:1.2]: Reduces the amount of light entering the MOS sensor to 1/16.
[ND:0.6]: Reduces the amount of light entering the MOS sensor to 1/4.
[ND:CLR]: The ND filter is not used.
Special recording function
Displays the status of special recording function.
Message display area
Displays the message such as the camera status or the warning.
Level gauge
Tilt in horizontal direction or vertical direction can be checked.
Displays only on the LCD monitor.
Wireless LAN connection status
Displays the connection status of the wireless LAN.
External equipment recording operation control status (<SDI OUT>/<HDMI> terminal)
Displays the control status of the recording start and recording stop on the external equipment connected to the <SDI OUT> terminal and the <HDMI> terminal.
[S/H]: Recording instruction is output to the output from the <SDI OUT> terminal, <HDMI> terminal.
[S/H]: Pause instruction is output to the output from the <SDI OUT> terminal, <HDMI> terminal.
[SDI]: Recording instruction is output to the output from the <SDI OUT> terminal.
[SDI]: Pause instruction is output to the output from the <SDI OUT> terminal.
[HDMI]: Recording instruction is output to the output from the <HDMI> terminal.
[HDMI]: Pause instruction is output to the output from the <HDMI> terminal.
Waveform monitor
Displays the video status in waveform or vector.
Displays only on the LCD monitor.
IR shooting
Displays when the IR recording is set to enable.
Electronic image stabilization function/digital zoom
Displays when the electronic image stabilization function is set or the digital zoom is enabled.