[SCENE FILE SETTINGS]

Sets the detailed image quality adjustment of the camera video.

[WHITE]/[BLACK]/[EI] are enabled only when [MENU] → [SYSTEM SETTINGS] → [COLOR SETTINGS] → [MAIN] is set to anything other than [V-Log].

Item

Description of settings

[NAME EDIT]

Edits the name of the scene file selected in the scene file menu. (Maximum eight characters)

[SCENE DATA]

[LOAD]

Selects and reads the scene file saved in the internal memory of the camera.

[YES], [NO]

[SAVE]

Saves the current setting value as a scene file in the memory inside the camera by specifying the title and the file number.

[YES], [NO]

[INITIALIZE]

Returns the selected scene file (one to five) to the factory setting.

[YES], [NO]

[WHITE]

[AWB]

Executes automatic white balance.

[EXECUTE], [CANCEL]

[VALUE]

Selects a value from a maximum of 12 registered values.

Preset values that can be selected in the factory settings are [3200K+0.0GMg], [4300K+0.0GMg], [5600K+0.0GMg], and [6300K+0.0GMg].

  • Factory setting: [3200K+0.0GMg]

[ADD]

Newly registers to the list. Newly registered value can be selected with [VALUE]. It will replace the currently selected value when there are 12 numbers registered already.

[DELETE]

Deletes from the list. Deletion is not possible when there is only one registered value.

[YES], [NO]

[R GAIN]

Adjusts the Rch gain.

[−200] - [200]

  • Factory setting: [0]

[G GAIN]

Adjusts the Gch gain.

[−200] - [200]

  • Factory setting: [0]

[B GAIN]

Adjusts the Bch gain.

[−200] - [200]

  • Factory setting: [0]

[AWB OFFSET]

Sets the Rch gain, Gch gain, and Bch gain values when the auto white balance is performed.

[ON]: Maintains and adds the values of [R GAIN], [G GAIN], and [B GAIN] after performing the auto white balance.

[OFF]: Resets the values of [R GAIN], [G GAIN], and [B GAIN] after performing auto white balance.

  • Factory setting: [OFF]

[SHOCKLESS WHITE]

Sets the transition time when switching preset values.

[OFF]: Values are immediately switched.

[1]: Switches in approximately one second.

[2]: Switches in approximately two seconds.

[3]: Switches in approximately five seconds.

  • Factory setting: [OFF]

[BLACK]

[ABB]

Executes automatic black balance. When executing automatic black balance, put the cap on the lens to keep any light from entering the image sensor.

[EXECUTE], [CANCEL]

[M.PED]

Sets the master pedestal level.

[−100] - [100]

  • Factory setting: [0]

[R PED]

Adjusts the Rch pedestal level.

[−100] - [100]

  • Factory setting: [0]

[G PED]

Adjusts the Gch pedestal level.

[−100] - [100]

  • Factory setting: [0]

[B PED]

Adjusts the Bch pedestal level.

[−100] - [100]

  • Factory setting: [0]

[ABB OFFSET]

Sets the Rch, Gch, and Bch pedestal levels after adjusting the automatic black balance.

[ON]: Maintains and adds the values of [R PED], [G PED], and [B PED] after performing the automatic black balance.

[OFF]: Resets the values of [R PED], [G PED], and [B PED] after performing the automatic black balance.

  • Factory setting: [OFF]

[EI]

[MODE]

Switches the EXPOSURE INDEX control unit.

[ISO], [dB]

  • Factory setting: [ISO]

[ISO SELECT]

Selects the operation of ISO.

[NATIVE ONLY], [800BASE], [5000BASE]

  • Factory setting: [NATIVE ONLY]

[NATIVE ISO]

Sets the value when [NATIVE ONLY] is selected.

[800ISO], [5000ISO]

This will be [400ISO] or [2500ISO] when [MAIN CODEC] is set to [AVC-Intra2K-LT]/[AVC-Intra-LT], and [MAIN PIXEL] is set to [2048×1080 CROP]/[1920×1080 CROP].

  • Factory setting: [800ISO]

[800BASE ISO]

Sets the value when [800BASE] is selected.

[200ISO], [250ISO], [320ISO], [400ISO], [500ISO], [640ISO], [800ISO], [1000ISO], [1250ISO], [1600ISO], [2000ISO], [2500ISO], [3200ISO], [4000ISO], [5000ISO], [6400ISO], [8000ISO], [10000ISO], [12800ISO]

This will be [200ISO], [250ISO], [320ISO], [400ISO], [500ISO], [640ISO], [800ISO], [1000ISO], [1250ISO], [1600ISO], [2000ISO], [2500ISO], [3200ISO], [4000ISO], [5000ISO], or [6400ISO] when [MAIN CODEC] is set to [AVC-Intra2K-LT]/[AVC-Intra-LT], and [MAIN PIXEL] is set to [2048×1080 CROP]/[1920×1080 CROP].

  • Factory setting: [800ISO]

[5000BASE ISO]

Sets the value when [5000BASE] is selected.

[1250ISO], [1600ISO], [2000ISO], [2500ISO], [3200ISO], [4000ISO], [5000ISO], [6400ISO], [8000ISO], [10000ISO], [12800ISO]

This will be [1250ISO], [1600ISO], [2000ISO], [2500ISO], [3200ISO], [4000ISO], [5000ISO], or [6400ISO] when [MAIN CODEC] is set to [AVC-Intra2K-LT]/[AVC-Intra-LT], and [MAIN PIXEL] is set to [2048×1080 CROP]/[1920×1080 CROP].

  • Factory setting: [5000ISO]

[GAIN MODE]

Sets the operation when [dB] is selected.

[NORMAL], [HIGH]

  • Factory setting: [NORMAL]

[GAIN SELECT]

Sets the value when [dB] is selected.

[−12dB], [−10dB], [−8dB], [−6dB], [−4dB], [−2dB], [0dB], [2dB], [4dB], [6dB], [8dB], [10dB], [12dB], [14dB]

This will be [−8dB], [−6dB], [−4dB], [−2dB], [0dB], [2dB], [4dB], [6dB], [8dB], [10dB], [12dB], or [14dB] when [MAIN CODEC] is set to [AVC-Intra2K-LT]/[AVC-Intra-LT], and [MAIN PIXEL] is set to [2048×1080 CROP]/[1920×1080 CROP].

When [GAMMA] → [GAMMA SELECT] is set to [VIDEO45]/[VIDEO50]/[BC GAMMA]

This will be set to [−6dB], [−4dB], [−2dB], [0dB], [2dB], [4dB], [6dB], [8dB], [10dB], [12dB], [14dB], [16dB], [18dB], or [20dB].

Also, this will be [−6dB], [−4dB], [−2dB], [0dB], [2dB], [4dB], [6dB], [8dB], [10dB], [12dB], [14dB] when [MAIN CODEC] is set to [AVC-Intra2K-LT]/[AVC-Intra-LT] and [MAIN PIXEL] is set to [2048×1080 CROP]/[1920×1080 CROP].

  • Factory setting: [0dB]

[GAIN OFFSET SW]

Sets whether to perform fine adjustment of control when [dB] is selected.

[ON], [OFF]

  • Factory setting: [OFF]

[GAIN OFFSET LEVEL]

Sets the fine adjustment level.

[0.0dB] - [0.9dB] (0.1 dB step)

  • Factory setting: [0.0dB]

[GAMMA]

([GAMMA])

[GAMMA SELECT]

Selects the gamma mode.

[V-Log], [BC GAMMA], or [HLG] can be selected only when [MAIN] is set to [SHADING].

[V-Log]: This is the gamma curve that can achieve tone and wide latitude.

[V-709]: This is a gamma curve equivalent to Varicam standard CINE-LIKE. A tone optimum for preview on the monitor can be achieved.

[V-406060]: A VARICAM-LOOK gamma curve with a latitude of 14+Stop. This is a setting focused on contrast.

[V-452080]/[V-452080L]: This is a VARICAM-LOOK gamma curve with a latitude of 14+Stop. This is a setting focused on soft texture.

[VIDEO45]: A BC-LOOK gamma curve with 600% dynamic range.

[VIDEO50]: A BC-LOOK gamma curve with 600% dynamic range. This is a setting focused on contrast.

[BC GAMMA]: A gamma curve with 600% dynamic range. The gamma factor can be adjusted in the range of [0.150] to [0.750].

[HLG]: Hybrid log gamma curve with 1600% dynamic range.

Color range equivalent to BT.2020 is automatically set.

Make adjustment in [MENU] → [SCENE FILE SETTINGS] → [HLG KNEE] when limiting the dynamic range to 1200%.

  • Factory setting: [V-709]

[MASTER GAMMA]

Adjusts the gamma characteristic.

[0.150] - [0.750]

  • Factory setting: [0.450]

[R GAMMA]

Adjusts the gamma characteristic of red against the master gamma.

[−75] - [+75]

  • Factory setting: [0]

[B GAMMA]

Adjusts the gamma characteristic of blue against the master gamma.

[−75] - [+75]

  • Factory setting: [0]

[BLACK GAMMA]

[SW]

Enables/disables the black gamma.

[ON], [OFF]

  • Factory setting: [OFF]

[BLACK R GAMMA]

Adjusts the gamma characteristic of red around black against the master gamma.

Can be controlled only when [GAMMA SELECT] is set to [BC GAMMA].

[−20] - [+20]

  • Factory setting: [0]

[BLACK MASTER GAMMA]

Adjusts the gamma characteristic around black.

[−48] - [+48]

  • Factory setting: [0]

[BLACK B GAMMA]

Adjusts the gamma characteristic of blue around black against the master gamma.

[−20] - [+20]

  • Factory setting: [0]

[KNEE]

([KNEE])

[KNEE SW]

Enables/disables the knee function.

[ON], [OFF]

  • Factory setting: [OFF]

[KNEE MODE]

Sets the knee operation mode.

[D RANGE]: Determines the dynamic range that can be represented by the [KNEE SLOPE] value. The dynamic range that can be represented does not change even if the [KNEE POINT] value changes.

[PRESS]: Determines the signal compression rate through the [KNEE SLOPE] value. The value of the dynamic range that can be represented changes when the [KNEE POINT] value changes.

  • Factory setting: [D RANGE]

[KNEE POINT]

Sets the position of the knee point.

[75%] - [109%] (1% step)

  • Factory setting: [85%]

[KNEE SLOPE]

Sets the knee inclination.

[0] - [100]

  • Factory setting: [100]

[HLG KNEE]

[KNEE SW]

Enables/disables the knee function when [GAMMA SELECT] is set to [HLG].

[ON], [OFF]

  • Factory setting: [OFF]

[KNEE POINT]

Sets the position of the knee point when [GAMMA SELECT] is set to [HLG].

[55%] - [100%] (1% step)

  • Factory setting: [55%]

[KNEE SLOPE]

Sets the knee inclination when [GAMMA SELECT] is set to [HLG].

[0] - [100]

  • Factory setting: [10]

[WHITE CLIP]

([WHITE CLIP])

[SW]

Switches the enable/disable of the white clip function.

[ON], [OFF]

  • Factory setting: [OFF]

[LEVEL]

Sets the white clip function level.

[90%] - [109%]

  • Factory setting: [109%]

[DETAIL]

[SW]

Switches the enable/disable of the detail function.

[ON], [OFF]

  • Factory setting: [OFF]

[CORING]

Sets the coring amount for the detail signal.

[0] - [60]

  • Factory setting: [1]

[MASTER LEVEL]

Sets the effect level for the detail signal.

[−31] - [31]

  • Factory setting: [0]

[FREQUENCY]

Sets the thickness of the detail.

[1] - [3]

  • Factory setting: [3]

[SKIN DETAIL]

([SKIN DETAIL])

[SW]

Switches enable/disable of the skin tone detail function.

[OFF], [ON]

  • Factory setting: [OFF]

[TABLE SELECT]

Selects the table for the skin tone detail.

[A], [B], [C], [A+B], [A+C], [B+C], [A+B+C]

  • Factory setting: [A]

[GET]

Sets whether to register the screen center color as the color by which the skin tone detail is applied.

[EXECUTE], [CANCEL]

[ZEBRA SW]

Sets whether to superimpose the zebra signal to the color by which the skin tone detail is applied.

[ON], [OFF]

  • Factory setting: [OFF]

[EFFECT LEVEL]

Sets the effective level of the skin tone detail. The higher the value, the more significant the effect.

[0] - [31]

  • Factory setting: [16]

[DETECT TABLE]

Selects the skin tone table of the subject that displays the skin tone detail.

[A], [B], [C]

  • Factory setting: [A]

[- I CENTER]

Sets the center position of the upper I axis (setting the area that displays the skin tone).

[0] - [255]

  • Factory setting: [35]

[- I WIDTH]

Sets the width of the area that displays the skin tone of the upper I axis that focus on [- I CENTER].

[0] - [255]

  • Factory setting: [55]

[- Q WIDTH]

Sets the width of the area that displays the skin tone of the upper Q axis that focus on [- I CENTER].

[0] - [127]

  • Factory setting: [22]

[- Q PHASE]

Sets the phase of the area that displays the skin tone regarding to the Q axis.

[0] - [255]

  • Factory setting: [0]

[CHROMA]

[LEVEL]

Sets the chroma level of PR and PB signals.

[OFF], [−99%] - [99%]

  • Factory setting: [0%]

[PHASE]

Fine adjusts the chroma phase of PR and PB signals.

[−31] - [31]

  • Factory setting: [0]

[LINEAR MATRIX]

([LINEAR MATRIX])

[SW]

Enables/disables the linear matrix function.

[ON], [OFF]

  • Factory setting: [OFF]

[(R-G)_N]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(R-G)_P]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(R-B)_N]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(R-B)_P]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(G-R)_N]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(G-R)_P]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(G-B)_N]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(G-B)_P]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(B-R)_N]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(B-R)_P]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(B-G)_N]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[(B-G)_P]

Adjusts the linear matrix.

[−127] - [127]

  • Factory setting: [0]

[COLOR CORRECTION]

([COLOR CORRECTION])

[SW]

Enables/disables the color correction function.

[ON], [OFF]

  • Factory setting: [OFF]

[R (SAT)]

Corrects red color saturation.

[−63] - [63]

  • Factory setting: [0]

[R (PHASE)]

Corrects the red hue.

[−63] - [63]

  • Factory setting: [0]

[P1(SAT)]

Corrects the color saturation between red and “between red and yellow”.

[−63] - [63]

  • Factory setting: [0]

[P1(PHASE)]

Corrects the hue between red and “between red and yellow”.

[−63] - [63]

  • Factory setting: [0]

[P2(SAT)]

Corrects the color saturation between red and yellow.

[−63] - [63]

  • Factory setting: [0]

[P2(PHASE)]

Corrects the hue between red and yellow.

[−63] - [63]

  • Factory setting: [0]

[P3(SAT)]

Corrects the color saturation between yellow and “between yellow and red”.

[−63] - [63]

  • Factory setting: [0]

[P3(PHASE)]

Corrects the color saturation between yellow and “between yellow and red”.

[−63] - [63]

  • Factory setting: [0]

[Yl (SAT)]

Corrects yellow color saturation.

[−63] - [63]

  • Factory setting: [0]

[Yl (PHASE)]

Corrects the yellow hue.

[−63] - [63]

  • Factory setting: [0]

[P4(SAT)]

Corrects the color saturation between yellow and “between yellow and green”.

[−63] - [63]

  • Factory setting: [0]

[P4(PHASE)]

Corrects the hue between yellow and “between yellow and green”.

[−63] - [63]

  • Factory setting: [0]

[P5(SAT)]

Corrects the color saturation between yellow and green.

[−63] - [63]

  • Factory setting: [0]

[P5(PHASE)]

Corrects the hue between yellow and green.

[−63] - [63]

  • Factory setting: [0]

[P6(SAT)]

Corrects the color saturation between “between yellow and green” and green.

[−63] - [63]

  • Factory setting: [0]

[P6(PHASE)]

Corrects the hue between “between yellow and green” and green.

[−63] - [63]

  • Factory setting: [0]

[G (SAT)]

Corrects green color saturation.

[−63] - [63]

  • Factory setting: [0]

[G (PHASE)]

Corrects the green hue.

[−63] - [63]

  • Factory setting: [0]

[P7(SAT)]

Corrects the color saturation between green and “between green and cyan”.

[−63] - [63]

  • Factory setting: [0]

[P7(PHASE)]

Corrects the hue between green and “between green and cyan”.

[−63] - [63]

  • Factory setting: [0]

[P8(SAT)]

Corrects the color saturation between green and cyan.

[−63] - [63]

  • Factory setting: [0]

[P8(PHASE)]

Corrects the hue between green and cyan.

[−63] - [63]

  • Factory setting: [0]

[P9(SAT)]

Corrects the color saturation between “between green and cyan” and cyan.

[−63] - [63]

  • Factory setting: [0]

[P9(PHASE)]

Corrects the hue between “between green and cyan” and cyan.

[−63] - [63]

  • Factory setting: [0]

[Cy (SAT)]

Corrects cyan color saturation.

[−63] - [63]

  • Factory setting: [0]

[Cy (PHASE)]

Corrects the cyan hue.

[−63] - [63]

  • Factory setting: [0]

[P10(SAT)]

Corrects the color saturation between cyan and “between cyan and blue”.

[−63] - [63]

  • Factory setting: [0]

[P10(PHASE)]

Corrects the hue between cyan and “between cyan and blue”.

[−63] - [63]

  • Factory setting: [0]

[P11(SAT)]

Corrects the color saturation between cyan and blue.

[−63] - [63]

  • Factory setting: [0]

[P11(PHASE)]

Corrects the hue between cyan and blue.

[−63] - [63]

  • Factory setting: [0]

[P12(SAT)]

Corrects the color saturation between “between cyan and blue” and blue.

[−63] - [63]

  • Factory setting: [0]

[P12(PHASE)]

Corrects the hue between “between cyan and blue” and blue.

[−63] - [63]

  • Factory setting: [0]

[B (SAT)]

Corrects blue color saturation.

[−63] - [63]

  • Factory setting: [0]

[B (PHASE)]

Corrects the blue hue.

[−63] - [63]

  • Factory setting: [0]

[P13(SAT)]

Corrects the color saturation between blue and “between blue and magenta”.

[−63] - [63]

  • Factory setting: [0]

[P13(PHASE)]

Corrects the hue between blue and “between blue and magenta”.

[−63] - [63]

  • Factory setting: [0]

[P14(SAT)]

Corrects the color saturation between blue and magenta.

[−63] - [63]

  • Factory setting: [0]

[P14(PHASE)]

Corrects the hue between blue and magenta.

[−63] - [63]

  • Factory setting: [0]

[P15(SAT)]

Corrects the color saturation between “between blue and magenta” and magenta.

[−63] - [63]

  • Factory setting: [0]

[P15(PHASE)]

Corrects the hue between “between blue and magenta” and magenta.

[−63] - [63]

  • Factory setting: [0]

[Mg (SAT)]

Corrects magenta color saturation.

[−63] - [63]

  • Factory setting: [0]

[Mg (PHASE)]

Corrects the magenta hue.

[−63] - [63]

  • Factory setting: [0]

[P16(SAT)]

Corrects the color saturation between magenta and “between magenta and red”.

[−63] - [63]

  • Factory setting: [0]

[P16(PHASE)]

Corrects the hue between magenta and “between magenta and red”.

[−63] - [63]

  • Factory setting: [0]

[P17(SAT)]

Corrects the color saturation between magenta and red.

[−63] - [63]

  • Factory setting: [0]

[P17(PHASE)]

Corrects the hue between magenta and red.

[−63] - [63]

  • Factory setting: [0]

[P18(SAT)]

Corrects the color saturation between “between magenta and red” and red.

[−63] - [63]

  • Factory setting: [0]

[P18(PHASE)]

Corrects the hue between “between magenta and red” and red.

[−63] - [63]

  • Factory setting: [0]