[OUTPUT SEL]

Configure the settings regarding video output from <SDI OUT>, <HDMI OUT>, <GENLOCK IN/VIDEO OUT>, or <TC IN/OUT> terminal.

Item

Description of settings

[SDI OUT]

Selects video output from the <SDI OUT> terminal.

[ON]: Outputs video.

[OFF]: Does not output video.

  • Factory setting: [OFF]

[SDI&HDMI SELECT]

Selects output signals from the <SDI OUT> terminal and <HDMI OUT> terminal.

[SYSTEM MODE]: Follows the setting in [SYSTEM MODE] → [LINE&FREQ].

[1080i]: Converts into interlaced signals and outputs them when [1080-59.94P] or [1080-50P] is selected in [SYSTEM MODE] → [LINE&FREQ]. This cannot be selected when other settings are made.

[DOWNCON]: Down converts to SD signal and outputs.

  • Factory setting: [SYSTEM MODE]

[3G-SDI OUT]

Selects 1080P signals of the HD SDI output in 1080P mode.

[LEVEL-A]: Selects the LEVEL-A method.

[LEVEL-B]: Selects the LEVEL-B DL method.

  • Factory setting: [LEVEL-B]

[SDI OUT CHAR]

Selects whether to superimpose characters on <SDI OUT> terminal output images.

[ON]: Superimposes.

[OFF]: Does not superimpose.

  • Factory setting: [OFF]

[SDI EDH]

Selects whether to superimpose EDH when output from the <SDI OUT> terminal is SD signal (480i and 576i).

[ON]: Superimposes.

[OFF]: Does not superimpose.

  • Factory setting: [ON]

[HD SDI REMOTE]

Sets whether to use the control function of recording operation for an external device (such as a recorder) connected to the <SDI OUT> terminal at HD SDI output.

[ON]: Controls the recording operation of the external device.

[OFF]: Does not control the recording operation of the external device.

  • Factory setting: [OFF]

[DOWNCON MODE]

Selects the mode of the down converter output signal mode from the <SDI OUT> or <GENLOCK IN/VIDEO OUT> terminal in HD mode (1080P, 1080i, or 720P).

[SIDE CROP], [LETTER BOX], [SQUEEZE]

  • Factory setting: [LETTER BOX]

[DOWNCON SETTING]

[DETAIL]

Turns detail function for the down converter output signal [ON]/[OFF].

[ON], [OFF]

The down converter output signal contains detail components set during HD signal processing.

This setting superimposes the detail components exclusive to down converter output to that signal.

  • Factory setting: [ON]

[H.DTL LEVEL]

Sets horizontal detail correction level for the down converter output signal.

[0]…[31]

  • Factory setting: [8]

[V.DTL LEVEL]

Sets vertical detail correction level for the down converter output signal.

[0]…[31]

  • Factory setting: [4]

[DTL CORING]

Sets the detail noise removal level.

[0]…[15]

  • Factory setting: [1]

[H.DTL FREQ]

Selects the horizontal detail frequency.

[2.5MHz], [3MHz], [3.5MHz], [4MHz], [4.5MHz]

  • Factory setting: [3.5MHz]

[VIDEO OUT]

Selects the <GENLOCK IN/VIDEO OUT> terminal output [ON]/[OFF].

[ON]: Performs output.

[OFF]: Stops output.

  • Factory setting: [OFF]

[VIDEO OUT CHAR]

Selects whether to superimpose characters on <GENLOCK IN/VIDEO OUT> terminal output images.

[ON]: Superimposes.

[OFF]: Does not superimpose.

  • Factory setting: [ON]

[VIDEO OUT ZEBRA]

Selects whether the zebra pattern is superimposed over the output video signals from the<GENLOCK IN/VIDEO OUT> terminal.

[ON]: Superimposes.

[OFF]: Does not superimpose.

  • Factory setting: [OFF]

[TC OUT]

Sets the type of time code output from the <TC IN/OUT> terminal.

[TCG]: Outputs the time code generator value of the camera at all times.

[TCG/TCR]: Outputs the time code generator value for camera image output, and the time code value of the video being played back for video playback output.

  • Factory setting: [TCG]

[TC OUTPUT REF]

Sets the output delay of time code output from the <TC IN/OUT> terminal.

[RECORDING]: Outputs the recorded time code with no delay. This is used when performing simultaneous recording on two cameras with the time code of this camera as the master.

[VIDEO OUT]: Matches to output images.

  • Factory setting: [VIDEO OUT]